Disclaimer
How to change rear wheel bearing on PEUGEOT Partner Origin Combispace (G_) – replacement guide
downloads:
0
Views:
5
Important!
This replacement procedure can be used for:
PEUGEOT Partner Origin Combispace (G_) 1.9 D, PEUGEOT Partner Origin Combispace (G_) 1.6 HDi, PEUGEOT Partner Origin Combispace (G_) 1.4 … View more
The steps may slightly vary depending on the car design.
PEUGEOT Partner Origin Combispace (G_) 1.9 D, PEUGEOT Partner Origin Combispace (G_) 1.6 HDi, PEUGEOT Partner Origin Combispace (G_) 1.4 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for Partner Origin Combispace (G_) and other PEUGEOT models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Copper grease
Torx bit T30
Drive socket # 32
Drive socket # 34
Wheel impact socket #19
Torque wrench
Flat chisel
Hammer
Tap wrench
Impact screwdriver
Rubber mallet
3-Arm Gear Puller
Crow bar
Wheel chock
Replacement: wheel bearing – PEUGEOT Partner Origin Combispace (G_). AUTODOC experts recommend:
- Do not re-use the bearing assembly of your PEUGEOT Partner Origin Combispace (G_) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- Warning! Shut down the engine before starting any work – PEUGEOT Partner Origin Combispace (G_).
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: wheel bearing – PEUGEOT Partner Origin Combispace (G_). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean the brake drum. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the brake drum fastening. Use Torx T30. Use an impact screwdriver. Use a hammer. - Step 8
Remove the brake drum. Use a crowbar. Use a hammer.Replacement: wheel bearing – PEUGEOT Partner Origin Combispace (G_). AUTODOC recommends:Examine the brake drum. Replace it if necessary. - Step 9
Remove the hub bearing protection cap. Use a crowbar. Use a hammer.Replacement: wheel bearing – PEUGEOT Partner Origin Combispace (G_). Tip from AUTODOC:Some cars are not equipped with wheel hub caps. - Step 10
Unstake the wheel hub retaining nut. Use a flat metal-working chisel. Use a hammer. - Step 11
Unscrew the wheel hub axle nut. Use a drive socket #34. Use a tap wrench. - Step 12
Remove the hub and the bearing together, since they are a sealed unit. Use 3-Arm Gear Puller. - Step 13
Clean the hub bearing mounting seat. Use all-purpose cleaning spray. - Step 14
Install the new wheel hub with a bearing. - Step 15
Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 225 Nm torque.Replacement: wheel bearing – PEUGEOT Partner Origin Combispace (G_). Tip from AUTODOC experts:The wheel bearing unit must not tilt on the axle pin.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the PEUGEOT Partner Origin Combispace (G_) model
Popular maintenance tutorials for PEUGEOT Partner Origin Combispace (G_)
Complete guides for changing the Wheel bearings on different PEUGEOT PARTNER models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your PEUGEOT Partner Origin Combispace (G_)
View more
How to Safely Wash Your Car in Winter Without Damage | AUTODOC tips
Top 5 car noises you shouldn't ignore
How to unlock your car without a key | AUTODOC tips
Motorcycle fuel tank restoration
Most commonly replaced car parts on PEUGEOT PARTNER
Time to replace parts? Get even better deals in our Shop app.

SCAN ME


























