Important!

This replacement procedure can be used for:
FIAT QUBO (225) 1.3 D Multijet (225AXE1A, 225CXE1A, 225AXH1A, 225AXL1A,..., FIAT QUBO (225) 1.4 (225AXA1A), FIAT QUBO (225) 1.3 D Multijet (225CXB1A, 225AXB1A, 225CXB11, 225AXB11,..., FIAT QUBO (225) 1.4 Natural Power (225AXC1A), FIAT QUBO (225) 1.3 D Multijet (225AXG1A, 225CXG1A, 225AXG11, 225CXG11), FIAT QUBO (225) 1.4 (225AXA1A, 225CXA1A) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for QUBO (225) and other FIAT models

Alternative products

Wheel bearing kit

Replacement: wheel bearing – FIAT QUBO (225). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      All-purpose cleaning spray
                    
                      Copper grease 
                    
                      Drive socket # 12 
                    
                      Drive socket # 13 
                    
                      Drive socket # 17 
                    
                      Drive socket # 32 
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Tap wrench
                    
                      Hammer
                    
                      Rubber mallet
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

Replacement: wheel bearing – FIAT QUBO (225). AUTODOC experts recommend:

Do not re-use the bearing assembly of your FIAT QUBO (225) car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
All work should be done with the engine stopped.

Replacement: wheel bearing – FIAT QUBO (225). Use the following procedure:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. FIAT QUBO (225)
Step 5

Remove the wheel.
Step 6

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the brake caliper fastening. Use a drive socket #13. Use a ratchet wrench.
Step 8

Remove the brake caliper. Use a crowbar.

Replacement: wheel bearing – FIAT QUBO (225). AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 9

Remove the brake pads.
Step 10

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 11

Unscrew the caliper bracket fastening. Use a drive socket #17. Use a tap wrench.
Step 12

Remove the caliper bracket.
Step 13

Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
Step 14

Unscrew the brake disc fastening. Use a drive socket #12. Use a ratchet wrench.
Step 15

Remove the brake disc. Use a rubber mallet.
Step 16

Remove the hub bearing protection cap. Use a crowbar. Use a hammer.

Replacement: wheel bearing – FIAT QUBO (225). Tip from AUTODOC experts:
Some cars are not equipped with wheel hub caps.
Step 17

Unscrew the wheel hub axle nut. Use a drive socket #32. Use a tap wrench.
Step 18

Remove the hub and the bearing together, since they are a sealed unit.
Step 19

Clean the hub bearing mounting seat. Use all-purpose cleaning spray.
Step 20

Install the new wheel hub with a bearing.
Step 21

Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 224 Nm torque.

Replacement: wheel bearing – FIAT QUBO (225). Tip:
The wheel bearing unit must not tilt on the axle pin.
Step 22

Install the hub bearing protection cap. Use a rubber mallet.
Step 23

Treat the hub where it contacts the brake disk. Use copper grease.
Step 24

Install the brake disc.
Step 25

Tighten the brake disc fastening. Use a drive socket #12. Use a torque wrench. Tighten it to 10 Nm torque.
Step 26

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – FIAT QUBO (225). After applying the spray, wait a few minutes.
Step 27

Install the brake caliper bracket.
Step 28

Tighten the brake caliper bracket. Use a drive socket #17. Use a torque wrench. Tighten it to 62 Nm torque.
Step 29

Install the brake pads.
Step 30

Install the brake caliper and fix it. Use a drive socket #13. Use a torque wrench. Tighten it to 30 Nm torque.
Step 31

Clean the brake disk surface. Use a wire brush.

Step 32

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 33

Clean the brake disk surface. Use a brake cleaner.

Replacement: wheel bearing – FIAT QUBO (225). Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 34

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. FIAT QUBO (225)
Step 35

Screw in the wheel bolts. Use wheel impact socket #17.
Step 36

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 120 Nm torque.
Step 37

Remove the jacks and chocks.

Comments – 2

A. G.

29.01.2024 09:16

Member

Fiat Qubo has drum brakes in the rear, this tutorial use disc brakes -_-
- Jessica_L
  
  29.01.2024 09:49
  
  Moderator
  
  This manual shows the procedure for replacing a similar part on another vehicle.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FIAT Qubo (225) model

Fiat Qubo tyre size

How to change front anti roll bar links on FIAT QUBO (225) – replacement guide

Free download PDF
1.7 MB
How to change front lower arm on FIAT Qubo (225) – replacement guide

Free download PDF
2.11 MB
How to change front brake pads on FIAT QUBO (225) – replacement guide

Free download PDF
1.61 MB
How to change front brake discs on FIAT QUBO (225) – replacement guide

Free download PDF
2.29 MB
How to change serpentine belt on FIAT Qubo (225) – replacement guide

Free download PDF
1.39 MB
How to change spark plugs on FIAT QUBO (225) – replacement guide

Free download PDF
1.46 MB

How to change wheel bearing on a car – replacement tutorial

Universal

Free download PDF
2.41 MB
How to change front wheel bearing on Fiat Punto 188 – replacement guide

Free download PDF
2.05 MB
How to change rear wheel bearing on Fiat Bravo 2 – replacement guide

Free download PDF
2.49 MB
How to change rear wheel bearing on Fiat Punto 188 – replacement guide

Free download PDF
1.47 MB
How to change rear wheel bearing on Fiat Panda 169 – replacement guide

Free download PDF
1.57 MB
How to change front wheel bearing on Fiat Panda 169 – replacement guide

Free download PDF
4.42 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

TOP 5 mistakes during DIY oil change | AUTODOC tips

36K views

Published on: 17/06/2021
How to Order Car Parts Online: Avoid These 5 Common Pitfalls

4K views

Published on: 10/03/2022
5 tools that make car repair incredibly simple | AUTODOC tips

47K views

Published on: 25/01/2024
5 more brake repair mistakes | Stop making these brake repair mistakes

9K views

Published on: 22/01/2025