Important!

This replacement procedure can be used for:
FORD C-MAX (DM2) 1.6, FORD C-MAX (DM2) 1.8 Flexifuel, FORD C-MAX (DM2) 2.0, FORD C-MAX (DM2) 1.6 TDCi, FORD C-MAX (DM2) 1.6 TDCi, FORD C-MAX (DM2) 2.0 TDCi, FORD C-MAX (DM2) 2.0 TDCi, FORD C-MAX (DM2) 1.8 TDCi … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Strut Mount for C-MAX (DM2) and other FORD models

Alternative products

Top strut mount

Replacement: strut mount – FORD C-MAX (DM2). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Drive socket # 10 
                    
                      Drive socket # 13 
                    
                      Drive socket # 16 
                    
                      Combination spanner #13
                    
                      Combination spanner #16
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Adjustable wrench
                    
                      Vice
                    
                      Wheel impact socket #19
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: strut mount – FORD C-MAX (DM2). Tip from AUTODOC experts:

The replacement procedure is identical for the mounts of the right and left shock absorbers of the rear suspension.
Both mounts of the rear shock struts should be replaced simultaneously.
All work should be done with the engine stopped.

Replacement: strut mount – FORD C-MAX (DM2). Take the following steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: strut mount – FORD C-MAX (DM2). AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Support the arm. Use a hydraulic transmission jack.
Step 7

Clean the fasteners of the shock absorber upper mount. Use a wire brush. Use WD-40 spray.
Step 8

Unscrew the shock absorber mount fastening. Use a drive socket #10. Use a ratchet wrench.
Step 9

Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray.
Step 10

Unscrew the lower fastener of the shock absorber. Use a drive socket #16. Use a ratchet wrench. Use a tap wrench.

AUTODOC recommends:
Important! Hold the shock absorber while unscrewing the fastening bolts. FORD C-MAX (DM2)
Step 11

Remove the shock absorber.
Step 12

Grip the shock absorber in a vice.
Step 13

Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray.
Step 14

Remove the shock absorber piston rod fastening. Use a combination spanner #13.
Step 15

Remove the shock absorber mount, boot and bump stop.
Step 16

Install the new mount, boot, and bump stop on the shock absorber.
Step 17

Screw the shock strut piston rod upper fastening. Use a combination spanner #13. Use a drive socket #13. Use an adjustable wrench. Use a torque wrench. Tighten it to 25 Nm torque.
Step 18

Clean the shock absorber mounting seats. Use a wire brush. Use WD-40 spray.
Step 19

Place the shock absorber in the wheel arch and secure it.
Step 20

Install the shock absorber mount using the center hole as a guide.
Step 21

Screw in the shock absober mount fastener. Use a drive socket #10. Use a ratchet wrench.

Step 22

Support the arm. Use a hydraulic transmission jack.
Step 23

Tighten the lower fastener of the shock absorber. Use a drive socket #16. Use a torque wrench. Tighten it to 103 Nm torque.
Step 24

Tighten the shock absorber mount fasteners. Use a drive socket #10. Use a torque wrench. Tighten it to 25 Nm torque.
Step 25

Remove the support from under the rear arm.
Step 26

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 27

Install the wheel.

Replacement: strut mount – FORD C-MAX (DM2). Tip:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 28

Screw in the wheel bolts. Use wheel impact socket #19.
Step 29

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 Nm torque.
Step 30

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FORD C-Max (DM2) model

Ford C-Max DM2 tyre size

How to change front strut mount on FORD C-MAX (DM2) – replacement guide

Free download PDF
2.79 MB
How to change front lower arm on FORD C-Max (DM2) – replacement guide

Free download PDF
2.6 MB
How to change rear suspension lower control arm on FORD C-MAX (DM2) – replacement guide

Free download PDF
1.29 MB
How to change rear wheel bearing on FORD C-MAX (DM2) – replacement guide

Free download PDF
2.25 MB
How to change front wheel bearing on FORD C-MAX (DM2) – replacement guide

Free download PDF
3.82 MB
How to change track rod end on FORD C-MAX (DM2) – replacement guide

Free download PDF
1.38 MB

How to change rear strut mount on FORD Grand C-Max (DXA/CB7, DXA/CEU) – replacement guide

Free download PDF
2.65 MB
How to change rear strut mount on FORD C-Max II (DXA/CB7, DXA/CEU) – replacement guide

Free download PDF
2.63 MB
How to change front strut mount on FORD C-MAX (DM2) – replacement guide

Free download PDF
2.79 MB
How to change strut mount on a car – replacement tutorial

Universal

Free download PDF
1.04 MB
How to change front strut mount on Ford Focus MK2 – replacement guide

Free download PDF
3.89 MB
How to change a front suspension strut mount on the Ford Transit Mk7 van – replacement guide

Free download PDF
4.44 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Don’t Replace, Restore: Fixing Damaged Threads at Home

8K views

Published on: 04/05/2023
How to make an injector test bench yourself

5K views

Published on: 30/01/2025
DIY vehicle AC compressor restoration

582K views

Published on: 28/11/2024
How to Swap an M50 Engine in a BMW E30 Turbo | AUTODOC Project

2K views

Published on: 15/02/2021