Important!

This replacement procedure can be used for:
AUDI TT Coupe (8J3) 2.0 TFSI, AUDI TT Coupe (8J3) 2.0 TFSI quattro, AUDI TT Coupe (8J3) 2.5 RS quattro, AUDI TT Coupe (8J3) 2.0 TFSI, AUDI TT Coupe (8J3) 3.2 V6 quattro, AUDI TT Coupe (8J3) 1.8 TFSI, AUDI TT Coupe (8J3) 2.0 TDI quattro, AUDI TT Coupe (8J3) 2.0 TFSI quattro, AUDI TT Coupe (8J3) 2.5 RS quattro, AUDI TT Coupe (8J3) 2.0 TFSI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Strut Mount for TT Coupe (8J3) and other AUDI models

Alternative products

Top strut mount

Replacement: strut mount – AUDI TT (8J3). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Drive socket # 14 
                    
                      Drive socket # 15 
                    
                      Drive socket # 18 
                    
                      Drive socket # 21 
                    
                      Combination spanner #14
                    
                      Combination spanner #18
                    
                      Combination spanner #21
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Tap wrench
                    
                      Vice
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: strut mount – AUDI TT (8J3). AUTODOC recommends:

The replacement procedure is identical for the mounts of the right and left shock absorbers of the rear suspension.
Both mounts of the rear shock struts should be replaced simultaneously.
All work should be done with the engine stopped.

Replacement: strut mount – AUDI TT (8J3). Take the following steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. AUDI TT (8J3)
Step 5

Remove the wheel.
Step 6

Support the arm. Use a hydraulic transmission jack.
Step 7

Unscrew the fastener connecting the control arm to the rear knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 8

Lower the hydraulic transmission jack by 10-15 cm.

Replacement: strut mount – AUDI TT (8J3). Tip from AUTODOC experts:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 9

Remove the spring.
Step 10

Unscrew the lower fastener of the shock absorber. Use a drive socket #21. Use a tap wrench.
Step 11

Unscrew the upper fastener of the shock absorber. Use a drive socket #15. Use a ratchet wrench.

Replacement: strut mount – AUDI TT (8J3). Tip:
To avoid injuries, hold the shock absorber when undoing the fastening bolts.
Step 12

Remove the shock absorber.

Step 13

Grip the shock absorber in a vice.
Step 14

Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray.
Step 15

Remove the shock absorber piston rod fastening. Use a combination spanner #14.
Step 16

Remove the shock absorber mount, boot and bump stop.
Step 17

Install the new mount, boot, and bump stop on the shock absorber.
Step 18

Fix the shock absorber mount. Use a combination spanner #14. Use a drive socket #14. Use a torque wrench. Tighten it to 25 Nm torque.
Step 19

Release the vice and take out the shock absorber.
Step 20

Place the shock absorber in the wheel arch and secure it.

AUTODOC recommends:
AUDI TT (8J3) – To avoid injury, hold the shock absorber while screwing in the fastening bolts.
Step 21

Tighten the shock absorber mount fasteners. Use a drive socket #15. Use a torque wrench. Tighten it to 50 Nm torque.+45°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 22

Clean the shock absorber fasteners. Use WD-40 spray.
Step 23

Tighten the lower fastener of the shock absorber. Use a drive socket #21. Use a torque wrench. Tighten it to 180 Nm torque.

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 24

Install the spring.
Step 25

Support the arm. Use a hydraulic transmission jack.
Step 26

Tighten the fasteners connecting the control arm to the rear knuckle. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. Tighten it to 90 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 27

Remove the support from under the rear arm.

AUTODOC recommends:
Replacement: strut mount – AUDI TT (8J3). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 28

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 29

Install the wheel.

Replacement: strut mount – AUDI TT (8J3). Tip from AUTODOC:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 30

Screw in the wheel bolts. Use wheel impact socket #17.
Step 31

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 120 Nm torque.

Step 32

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the AUDI TT Coupe (8J3) model

Audi TT 8J tyre size

How to change rear suspension lower trailing arm on AUDI TT Coupe (8J3) – replacement guide

Free download PDF
1.66 MB
How to change front lower arm on AUDI TT Coupe (8J3) – replacement guide

Free download PDF
2.1 MB
How to change rear suspension lower control arm on AUDI TT Coupe (8J3) – replacement guide

Free download PDF
1.62 MB
How to change front strut mount on AUDI TT Coupe (8J3) – replacement guide

Free download PDF
3.86 MB
How to change rear anti roll bar links on AUDI TT Coupe (8J3) – replacement guide

Free download PDF
1.37 MB
How to change rear wheel bearing on AUDI TT Coupe (8J3) – replacement guide

Free download PDF
2.22 MB

How to change front strut mount on AUDI TT Coupe (8J3) – replacement guide

Free download PDF
3.86 MB
How to change front strut mount on AUDI TT Coupe (8N3) – replacement guide

Free download PDF
3.8 MB
How to change rear strut mount on AUDI TT Coupe (8N3) – replacement guide

Free download PDF
2.84 MB
How to change front strut mount on AUDI TT Coupe (FV3, FVP) – replacement guide

Free download PDF
3.41 MB
How to change front strut mount on AUDI TT Roadster (8N9) – replacement guide

Free download PDF
3.8 MB
How to change rear strut mount on AUDI TT Roadster (8N9) – replacement guide

Free download PDF
2.84 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

5 mistakes made when washing the engine | AUTODOC tips

31K views

Published on: 22/04/2021
Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide

3K views

Published on: 23/03/2023
Prevent Engine Damage: How to Identify Rocker Cover Gasket Issues and Proper Replacement | AUTODOC

5K views

Published on: 03/12/2020
TOP 5 mistakes during DIY oil change | AUTODOC tips

36K views

Published on: 17/06/2021