Disclaimer
How to change rear coil springs on Renault Clio 2 – replacement guide
downloads:
14
Views:
136
Important!
This replacement procedure can be used for:
RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.2 (BB0A, BB0F, BB10, BB1K, BB28, BB2D, BB2H, CB0A,..., RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.4 (B/CB0C, B/CB0S), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.6 (B/CB0D, BB00), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.6 16V (BB01, BB0H, BB0T, BB14, BB1D, BB1R, BB2KL, BB3G..., RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.9 D (B/CB0E, BB0J), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.4 16V (B/CB0L), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.9 dTi (B/CB0U), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.4 16V (B/CB0P, BB13), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/CB07), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/CB08), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi, RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.0, RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.9 D (B/CB0J), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.2, RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/CB03), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.2 LPG (BB0A, CB0A), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/C2J), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/CB3M), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (BB3N, CB3N) … View more
The steps may slightly vary depending on the car design.
RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.2 (BB0A, BB0F, BB10, BB1K, BB28, BB2D, BB2H, CB0A,..., RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.4 (B/CB0C, B/CB0S), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.6 (B/CB0D, BB00), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.6 16V (BB01, BB0H, BB0T, BB14, BB1D, BB1R, BB2KL, BB3G..., RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.9 D (B/CB0E, BB0J), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.4 16V (B/CB0L), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.9 dTi (B/CB0U), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.4 16V (B/CB0P, BB13), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/CB07), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/CB08), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi, RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.0, RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.9 D (B/CB0J), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.2, RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/CB03), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.2 LPG (BB0A, CB0A), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/C2J), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (B/CB3M), RENAULT CLIO II (BB0/1/2_, CB0/1/2_) 1.5 dCi (BB3N, CB3N) … View more
The steps may slightly vary depending on the car design.
How to change rear springs / rear coil springs on RENAULT CLIO 2 (C65) [TUTORIAL AUTODOC]

All the parts you need to replace – Springs for CLIO II (BB0/1/2_, CB0/1/2_) and other RENAULT models
Alternative products

Wire brush
WD-40 spray
Copper grease
Drive socket # 18
Wheel impact socket #19
Torque wrench
Hydraulic transmission jack
Wheel chock
Replacement: coil springs – Renault Clio 2. AUTODOC experts recommend:
- Both coil springs of the rear suspension should be replaced simultaneously.
- The replacement procedure is identical for the left and right coil springs of the rear suspension.
- Please note: all work on the car – Renault Clio 2 – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3
Raise the rear of the car and secure on supports. - Step 4
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. Renault Clio 2 - Step 5
Remove the wheel. - Step 6
Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Support the rear suspension beam. Use a hydraulic transmission jack. - Step 8
Unscrew the lower fastener of the shock absorber. Use a drive socket #18. - Step 9
Remove the fastening bolt. - Step 10
Detach the lower part of the shock absorber. - Step 11
Remove the mounting from under the rear axle beam.AUTODOC recommends:Replacement: coil springs – Renault Clio 2. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms. - Step 12
Support the rear suspension beam. Use a hydraulic transmission jack. - Step 13Unscrew the lower fastener of the shock absorber. Use a drive socket #18.Step 14Remove the fastening bolt.Step 15Detach the lower part of the shock absorber.Step 16
Remove the mounting from under the rear axle beam.AUTODOC recommends:Replacement: coil springs – Renault Clio 2. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms. - Step 17
Take out the spring. - Step 18
Clean the coil spring mounting seats. Use a wire brush. Use WD-40 spray. - Step 19
Install the coil spring together with the rubber mounts into the mounting seats. - Step 20
Support the rear suspension beam. Use a hydraulic transmission jack.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Clio II Hatchback (BB, CB) model
Popular maintenance tutorials for Renault Clio 2
Complete guides for changing the Springs on different RENAULT CLIO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT CLIO II (BB0/1/2_, CB0/1/2_)
View more
Why Checking Your Oil is Crucial for Engine Performance
Why Is the Windscreen Washer Not Spraying? Solution
Initial Car Inspection: What to Check Before You Buy
What to do if the ABS light comes on: DIY Diagnostics Tips
Most commonly replaced car parts on RENAULT CLIO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME

























