Important!

This replacement procedure can be used for:
HONDA CR-V II (RD_) 2.0 (RD5) … View more

The steps may slightly vary depending on the car design.

How to change Rear Springs on HONDA CR-V 2 TUTORIAL | AUTODOC

Alternative products

Coil spring

Replacement: coil springs – Honda CR-V II. List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner
                    
                      Copper grease
                    
                      Drive socket # 14
                    
                      Drive socket # 17
                    
                      Combination spanner #17
                    
                      HEX bit no.H6.
                    
                      Wheel impact socket #19
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Hydraulic strut spring compressor
                    
                      Flat Screwdriver
                    
                      Tap wrench
                    
                      Crow bar
                    
                      Hydraulic transmission jack
                    
                      Fender cover
                    
                      Wheel chock

Buy tools

Replacement: coil springs – Honda CR-V II. AUTODOC experts recommend:

Both coil springs of the rear suspension should be replaced simultaneously.
The replacement procedure is identical for the left and right coil springs of the rear suspension.
Please note: all work on the car – Honda CR-V II – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3

Raise the rear of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Honda CR-V II
Step 5

Remove the wheel.
Step 6

Clean the shock strut fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the lower fastener of the shock absorber strut. Use a drive socket #17. Use a tap wrench. Use a ratchet wrench.
Step 8

Remove the fastening bolt. Use a crowbar.
Step 9

Detach the bottom part of the shock strut. Use a crowbar.
Step 10

Lower the car.
Step 11

Open the boot lid.
Step 12

Remove the side plastic cover. Use a flat screwdriver.
Step 13

Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.
Step 14

Unscrew the top fastening of the shock strut mount. Use a drive socket #14. Use a ratchet wrench.

AUTODOC recommends:
Honda CR-V II – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
Step 15

Remove the suspension strut.
Step 16

Set the shock absorber strut on the spring compressor tool.

Replacement: coil springs – Honda CR-V II. Tip from AUTODOC experts:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 17

Compress the spring.
Step 18

Treat the shock strut rod. Use a wire brush. Use WD-40 spray.
Step 19

Remove the strut piston rod nut. Use a combination spanner #17. Use HEX No.H6. Use a ratchet wrench.
Step 20

Release the coil spring.
Step 21

Remove the top strut mount.
Step 22

Remove the spring.

AUTODOC recommends:
Replacement: coil springs – Honda CR-V II. Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
Step 23

Install the spring on the shock absorber.
Step 24

Install the upper strut mount and the strut mount bearing.
Step 25

Compress the spring.
Step 26

Tighten the shock strut piston rod nut. Use a combination spanner #17. Use HEX No.H6. Use a torque wrench. Tighten it to 29 Nm torque.

Replacement: coil springs – Honda CR-V II. Professionals recommend:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 27

Decompress the spring.

Step 28

Treat the shock strut rod. Use copper grease.

Step 29

Remove the assembled shock strut.
Step 30

Install the shock strut into the wheel arch.
Step 31

Screw the top fastening of the shock strut mount.

AUTODOC recommends:
Important! Hold the suspension strut while screwing in the fastening bolts. Honda CR-V II
Step 32

Tighten the upper fastener of the shock absorber strut mount. Use a drive socket #14. Use a torque wrench. Tighten it to 74 Nm torque.
Step 33

Treat the fasteners of the shock strut mount. Use copper grease.

Step 34

Install the side plastic panel.
Step 35

Close the lid of the luggage compartment.

Step 36

Lift the car using a jack or place it over an inspection pit.
Step 37

Attach the bottom part of the shock strut. Use a crowbar. Use a flat screwdriver.
Step 38

Install the fastening bolt. Use a crowbar. Use a drive socket #17. Use a ratchet wrench.
Step 39

Support the arm. Use a hydraulic transmission jack.
Step 40

Tighten the lower fastening of the shock absorber. Use a drive socket #17. Use a torque wrench. Tighten it to 93 nm torque.
Step 41

Remove the support from under the arm.

AUTODOC recommends:
Replacement: coil springs – Honda CR-V II. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 42

Treat the shock strut fasteners. Use copper grease.

Step 43

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 44

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 45

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Honda CR-V II
Step 46

Screw in the wheel bolts. Use wheel impact socket #19.
Step 47

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 108 nm torque.
Step 48

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the HONDA CR-V II (RD) model

Honda CR-V Mk2 tyre size

How to change rear suspension strut on Honda CR-V II – replacement guide

Free download PDF
2.54 MB
How to change front suspension strut on Honda CR-V II – replacement guide

Free download PDF
3.42 MB
How to change front coil springs on Honda CR-V II – replacement guide

Free download PDF
3.17 MB
How to change rear brake pads on Honda CR-V II – replacement guide

Free download PDF
1.52 MB
How to change front brake pads on Honda CR-V II – replacement guide

Free download PDF
1.71 MB
How to change rear brake discs on Honda CR-V II – replacement guide

Free download PDF
2.2 MB

How to change front coil springs on Honda CR-V II – replacement guide

Free download PDF
3.17 MB
How to change coil springs on a car – replacement tutorial

Universal

Free download PDF
1.91 MB
How to change rear coil springs on Honda Jazz GD – replacement guide

Free download PDF
1.93 MB
How to change front coil springs on Honda Accord VIII CU – replacement guide

Free download PDF
4.51 MB
How to change front coil springs on HONDA Accord VIII Estate (CW) – replacement guide

Free download PDF
4.48 MB
How to change front coil springs on VW Golf 6 – replacement guide

Free download PDF
4.16 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

TOP 8 mistakes car owners make | AUTODOC tips

14K views

Published on: 09/12/2021
Top 7 Manual Transmission Mistakes to Avoid | AUTODOC Tips

6K views

Published on: 20/10/2020
Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide

3K views

Published on: 23/03/2023
DIY manual gearbox restoration | Drivetrain restoration – Part 3

18K views

Published on: 14/11/2024