Important!

This replacement procedure can be used for:
FORD MONDEO III (B5Y) 1.8 16V, FORD MONDEO III (B5Y) 1.8 16V, FORD MONDEO III (B5Y) 2.0 16V, FORD MONDEO III (B5Y) 2.5 V6 24V, FORD MONDEO III (B5Y) 2.0 16V DI / TDDi / TDCi, FORD MONDEO III (B5Y) 2.0 16V TDDi / TDCi, FORD MONDEO III (B5Y) 2.0 TDCi, FORD MONDEO III (B5Y) 1.8 SCi, FORD MONDEO III (B5Y) 2.2 TDCi, FORD MONDEO III (B5Y) 3.0 V6 24V, FORD MONDEO III (B5Y) 2.2 TDCi, FORD MONDEO III (B5Y) 2.0 DI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Springs for MONDEO III (B5Y) and other FORD models

Coil spring

        Coil spring for Mondeo Mk3 Hatchback (B5Y) Petrol (110 hp)
      
        Coil spring for Mondeo Mk3 Hatchback (B5Y) Petrol (125 hp)
      
        Coil spring for Mondeo Mk3 Hatchback (B5Y) Petrol (146 hp)
      
        Coil spring for Mondeo Mk3 Hatchback (B5Y) Petrol (170 hp)
      
        Coil spring for Mondeo Mk3 Hatchback (B5Y) Diesel (90 hp)
      
        Coil spring for Mondeo Mk3 Hatchback (B5Y) Diesel (115 hp)
      
        Coil spring for Mondeo Mk3 Hatchback (B5Y) Diesel (130 hp)
      
        Coil spring for Mondeo Mk3 Hatchback (B5Y) Petrol (130 hp)
      
        Coil spring for Mondeo Mk3 Hatchback (B5Y) Diesel (155 hp)

Replacement: coil springs – FORD MONDEO III (B5Y). Tools you might need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Electronic spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Combination spanner #13
                      
                        Drive socket # 10
                      
                        Drive socket # 13
                      
                        Drive socket # 15
                      
                        Drive socket # 17
                      
                        Drive socket # 18
                      
                        Drive socket # 19
                      
                        Shock absorber socket
                      
                        HEX bit No.H6
                      
                        Wheel impact socket #19
                      
                        Ratchet wrench
                      
                        Nippers
                      
                        Tap wrench
                      
                        Hydraulic strut spring compressor
                      
                        Crow bar
                      
                        Hydraulic transmission jack
                      
                        Wheel chock

Buy tools

Replacement: coil springs – FORD MONDEO III (B5Y). AUTODOC experts recommend:

Both coil springs of the rear suspension should be replaced simultaneously.
The replacement procedure is identical for the left and right coil springs of the rear suspension.
All work should be done with the engine stopped.

Replacement: coil springs – FORD MONDEO III (B5Y). Use the following procedure:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. FORD MONDEO III (B5Y)
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a ratchet wrench.
Step 8

Remove the stabilizer rod.
Step 9

Clean the fastener of the parking brake cable. Use a wire brush. Use WD-40 spray.
Step 10

Release the parking brake cable. Use nippers. Use a crowbar.
Step 11

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 12

Unscrew the brake caliper fastening. Use a combination spanner #13.
Step 13

Remove the brake caliper. Use a crowbar.

Replacement: coil springs – FORD MONDEO III (B5Y). AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 14

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 15

Unscrew the fastener connecting the control arm to the rear knuckle. Use a drive socket #15. Use a ratchet wrench.
Step 16

Remove the fastening bolt. Detach the control arm.
Step 17

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 18

Unscrew the fastener connecting the control arm to the rear knuckle. Use a drive socket #15. Use a ratchet wrench.
Step 19

Remove the fastening bolt. Detach the control arm.
Step 20

Detach the ABS sensor connector.
Step 21

Clean the shock strut fasteners. Use a wire brush. Use WD-40 spray.
Step 22

Unscrew the fastener that connects the suspension strut to the rear knuckle. Use a drive socket #18. Use a ratchet wrench. Use a tap wrench.
Step 23

Remove the fastening bolt.
Step 24

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 25

Unscrew the fastener connecting the control arm to the rear knuckle. Use a drive socket #15. Use a ratchet wrench.
Step 26

Remove the fastening bolt. Detach the control arm.

Step 27

Support the rear knuckle. Use a hydraulic transmission jack.
Step 28

Release the fastener connecting the shock absorber to the rear knuckle. Use a special drive socket to remove the shock absorber. Use a ratchet wrench.
Step 29

Detach the shock absorber from the rear knuckle.
Step 30

Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.
Step 31

Unscrew the upper fasteners of the shock strut. Use a drive socket #10. Use a ratchet wrench.

AUTODOC recommends:
To avoid injuries, hold the shock strut when undoing the fastening bolts.
Step 32

Remove the suspension strut.
Step 33

Set the shock absorber strut on the spring compressor tool.

Replacement: coil springs – FORD MONDEO III (B5Y). AUTODOC recommends:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 34

Compress the spring.
Step 35

Treat the shock strut rod. Use a wire brush. Use WD-40 spray.
Step 36

Remove the strut piston rod nut. Use a drive socket #19. Use HEX No.H6. Use a ratchet wrench.
Step 37

Remove the top strut mount.
Step 38

Release the coil spring.
Step 39

Remove the spring.
Step 40

Remove the shock absorber dust cap and the bump stop.

AUTODOC recommends:
Replacement: coil springs – FORD MONDEO III (B5Y). Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
Step 41

Install the dust boot and bump stop on the shock absorber.
Step 42

Install the spring on the shock absorber.
Step 43

Compress the spring.
Step 44

Install the upper strut mount and the strut mount bearing.
Step 45

Tighten the shock strut piston rod nut. Use a drive socket #19. Use HEX No.H6. Use a torque wrench. Tighten it to 50 Nm torque.

AUTODOC recommends:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 46

Treat the shock strut rod. Use copper grease.
Step 47

Decompress the spring.
Step 48

Remove the assembled shock strut.
Step 49

Clean the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 50

Install the shock strut into the wheel arch.
Step 51

Secure the upper fasteners of the shock strut. Do not tighten it.

AUTODOC recommends:
Important! Hold the suspension strut while screwing in the fastening bolts. FORD MONDEO III (B5Y)
Step 52

Tighten the upper fasteners of the shock strut. Use a drive socket #10. Use a torque wrench. Tighten it to 25 Nm torque.
Step 53

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 54

Clean the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 55

Attach the shock absorber to the rear knuckle.
Step 56

Install the fastening bolt.
Step 57

Screw in the fastener connecting the shock absorber to the rear knuckle. Use a drive socket #18. Use a ratchet wrench.
Step 58

Attach the control arm. Install the fastening bolt.
Step 59

Screw in the fasteners connecting the control arm to the rear knuckle. Use a drive socket #15. Use a ratchet wrench.
Step 60

Attach the control arm. Install the fastening bolt.
Step 61

Screw in the fasteners connecting the control arm to the rear knuckle. Use a drive socket #15. Use a ratchet wrench.
Step 62

Attach the control arm. Install the fastening bolt.
Step 63

Screw in the fasteners connecting the control arm to the rear knuckle. Use a drive socket #15. Use a ratchet wrench.
Step 64

Raise the hydraulic transmission jack by 10-15 cm.
Step 65

Tighten the fasteners connecting the control arm to the rear knuckle. Use a drive socket #15. Use a torque wrench. Tighten it to 103 Nm torque.
Step 66

Tighten the fastener that connects the suspension strut to the rear knuckle. Use a drive socket #18. Use a torque wrench. Tighten it to 85 Nm torque.
Step 67

Remove the support from under the rear knuckle.

AUTODOC recommends:
Replacement: coil springs – FORD MONDEO III (B5Y). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 68

Treat the ABS sensor connector. Use dielectric grease.
Step 69

Attach the ABS sensor connector.
Step 70

Install the brake caliper and fix it. Use a drive socket #13. Use a torque wrench. Tighten it to 30 Nm torque.
Step 71

Install the parking brake cable into the brake caliper bracket. Use nippers. Use a crowbar.
Step 72

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 73

Ιnstall the transverse stabilizer link.
Step 74

Tighten the stabiliser link fastener. Use a drive socket #17. Use a ratchet wrench.
Step 75

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a torque wrench. Tighten it to 48 Nm torque.
Step 76

Treat the shock strut fasteners. Treat all joints of the stabiliser link. Treat the rear knuckle fasteners. Use copper grease.
Step 77

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 78

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: coil springs – FORD MONDEO III (B5Y). After applying the spray, wait a few minutes.
Step 79

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. FORD MONDEO III (B5Y)
Step 80

Screw in the wheel bolts. Use wheel impact socket #19.
Step 81

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 90 Nm torque.
Step 82

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the FORD Mondeo Mk3 Hatchback (B5Y) model.

Browse tyres

How to change rear suspension strut on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
4.37 MB
How to change front coil springs on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
4.35 MB
How to change front suspension strut on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
4.42 MB
How to change rear brake pads on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
1.51 MB
How to change front brake pads on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
1.49 MB
How to change rear brake discs on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
1.99 MB

How to change front coil springs on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
4.35 MB
How to change rear coil springs on Ford Mondeo BWY – replacement guide

Free download PDF
1.59 MB
How to change rear coil springs on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
4.03 MB
How to change front coil springs on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
4.11 MB
How to change coil springs on a car – replacement tutorial

Universal

Free download PDF
1.91 MB
How to change front coil springs on Ford Fiesta JA8 – replacement guide

Free download PDF
3.47 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Things you should never do with your manual transmission | AUTODOC tips

5K views

Published on: 20/10/2020
What to do if the belt squeals | AUTODOC tips

4K views

Published on: 04/03/2021
How to wash your car in winter | AUTODOC tips

3K views

Published on: 31/01/2024
3 things that cause engine damage | AUTODOC tips

9K views

Published on: 07/10/2021