Important!

This replacement procedure can be used for:
FORD Fiesta Mk6 Hatchback (JA8, JR8) 1.6 Ti, FORD Fiesta Mk6 Hatchback (JA8, JR8) 1.6 Ti, FORD Fiesta Mk6 Hatchback (JA8, JR8) 1.0 EcoBoost, FORD Fiesta Mk6 Hatchback (JA8, JR8) 1.0 EcoBoost, FORD Fiesta Mk6 Hatchback (JA8, JR8) 1.6 Ti, FORD Fiesta Mk6 Hatchback (JA8, JR8) 1.5 TDCi … View more

The steps may slightly vary depending on the car design.

How to change front springs / front coil springs on FORD FIESTA JA8 [TUTORIAL AUTODOC]

Alternative products

Coil spring

Replacement: coil springs – Ford Fiesta JA8. Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner
                    
                      Copper grease
                    
                      Combination spanner #13
                    
                      Combination spanner #15
                    
                      Combination spanner #18
                    
                      HEX bit no.H6.
                    
                      Drive socket # 10
                    
                      Drive socket # 13
                    
                      Drive socket # 15
                    
                      Drive socket # 18
                    
                      Wheel impact socket #19
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Clip removal tool
                    
                      Hydraulic strut spring compressor
                    
                      Hydraulic transmission jack
                    
                      Fender cover
                    
                      Wheel chock

Buy tools

Replacement: coil springs – Ford Fiesta JA8. AUTODOC recommends:

Both coil springs of the front suspension should be replaced simultaneously.
The replacement procedure is identical for the left and right coil springs of the front suspension.
All work should be done with the engine stopped.

Replacement: coil springs – Ford Fiesta JA8. Use the following procedure:

Step 1

Open the bonnet.
Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3

Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.
Step 4

Loosen the upper fastener of the shock strut mount. Use a combination spanner #13.
Step 5

Secure the wheels with chocks.
Step 6

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 7

Raise the front of the car and secure on supports.
Step 8

Unscrew the wheel bolts.

Replacement: coil springs – Ford Fiesta JA8. Professionals recommend:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 9

Remove the wheel.
Step 10

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 11

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #15. Use a ratchet wrench.
Step 12

Remove the stabilizer rod.
Step 13

Disconnect the ABS sensor wiring. Use a clip removal tool.
Step 14

Clean the fasteners connecting the brake hose to the shock strut. Use a wire brush. Use WD-40 spray.
Step 15

Disconnect the brake hose holder from the shock absorber strut. Use a drive socket #10. Use a ratchet wrench.
Step 16

Detach the brake hose from the shock strut.
Step 17

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 18

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #15. Use a drive socket #18. Use a ratchet wrench.
Step 19

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 20

Remove the fastening bolts.
Step 21

Disconnect the steering knuckle from the shock absorber strut.
Step 22

Unscrew the top fastening of the shock strut mount.

AUTODOC recommends:
Important! Hold the suspension strut while unscrewing the fastening bolts. Ford Fiesta JA8
Step 23

Remove the suspension strut.
Step 24

Set the shock absorber strut on the spring compressor tool.

Replacement: coil springs – Ford Fiesta JA8. AUTODOC experts recommend:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 25

Compress the spring.
Step 26

Treat the shock strut rod. Use a wire brush. Use WD-40 spray.
Step 27

Remove the strut piston rod nut. Use HEX No.H6. Use a drive socket #18. Use a ratchet wrench.
Step 28

Remove the top strut mount.
Step 29

Remove the shock absorber dust cap and the bump stop.
Step 30

Release the coil spring.
Step 31

Remove the spring.

Replacement: coil springs – Ford Fiesta JA8. Tip:
Τhoroughly examine the shock absorber mount, dust boot, bump stop. Replace them if necessary.
Step 32

Install the spring on the shock absorber.
Step 33

Compress the spring.
Step 34

Install the boot and a bump stop onto the shock absorber.
Step 35

Install the upper strut mount and the strut mount bearing.
Step 36

Tighten the shock strut piston rod nut. Use HEX No.H6. Use a drive socket #18. Use a torque wrench. Tighten it to 48 Nm torque.

Replacement: coil springs – Ford Fiesta JA8. Tip from AUTODOC experts:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 37

Decompress the spring.
Step 38

Treat the shock strut rod. Use copper grease.

Step 39

Remove the assembled shock strut.
Step 40

Treat the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 41

Install the shock strut into the wheel arch.
Step 42

Screw the top fastening of the shock strut mount. Do not tighten it.

AUTODOC recommends:
Ford Fiesta JA8 – To avoid injury, hold the suspension strut while screwing in the fastening bolts.
Step 43

Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 44

Fix the shock absorber strut on the steering knuckle.
Step 45

Install the fastening bolts.
Step 46

Screw in the fastener that connects the shock strut to the steering knuckle. Use a combination spanner #15. Use a drive socket #18. Use a ratchet wrench.
Step 47

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: coil springs – Ford Fiesta JA8. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 48

Fasten the brake hose on the strut.
Step 49

Connect the brake hose fastener to the shock absorber strut.
Step 50

Use a drive socket #10. Use a torque wrench. Tighten it to 7 Nm torque.
Step 51

Connect the ABS sensor wiring.
Step 52

Ιnstall the transverse stabilizer link.
Step 53

Tighten the stabiliser link fastener. Use a drive socket #15. Use a ratchet wrench.
Step 54

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #15. Use a torque wrench. Tighten it to 48 Nm torque.
Step 55

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #15. Use a drive socket #18. Use a torque wrench. Tighten it to 82 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 56

Treat the shock strut fasteners. Use copper grease.
Step 57

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 58

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 59

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. Ford Fiesta JA8
Step 60

Screw in the wheel bolts. Use wheel impact socket #19.
Step 61

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 110 Nm torque.
Step 62

Remove the jacks and chocks.
Step 63

Tighten the upper fastener of the shock absorber strut mount. Use a combination spanner #13. Use a drive socket #13. Use a torque wrench. Tighten it to 30 nm torque.
Step 64

Treat the fasteners of the shock strut mount. Use copper grease.
Step 65

Remove the fender protection cover.
Step 66

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FORD Fiesta Mk6 Hatchback (JA8, JR8) model

Ford Fiesta Mk6 tyre size

How to change front suspension strut on Ford Fiesta JA8 – replacement guide

Free download PDF
3.49 MB
How to change rear shock absorbers on Ford Fiesta JA8 – replacement guide

Free download PDF
2.18 MB
How to change front brake pads on Ford Fiesta JA8 – replacement guide

Free download PDF
1.61 MB
How to change front brake discs on Ford Fiesta JA8 – replacement guide

Free download PDF
1.88 MB
How to change rear brake discs on FORD Fiesta Mk6 Hatchback (JA8, JR8) – replacement guide

Free download PDF
2.04 MB
How to change front wheel bearing on Ford Fiesta JA8 – replacement guide

Free download PDF
4.06 MB

How to change rear coil springs on Ford Fiesta V JH JD – replacement guide

Free download PDF
2.74 MB
How to change front coil springs on Ford Fiesta V JH JD – replacement guide

Free download PDF
5.1 MB
How to change rear coil springs on FORD Fiesta Mk5 Van – replacement guide

Free download PDF
2.86 MB
How to change front coil springs on FORD Fiesta Mk5 Van – replacement guide

Free download PDF
5.15 MB
How to change coil springs on a car – replacement tutorial

Universal

Free download PDF
1.91 MB
How to change front coil springs on Ford Focus MK2 – replacement guide

Free download PDF
4.01 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY alternator repair | AUTODOC tips

2M views

Published on: 30/11/2022
5 mistakes made when washing the engine | AUTODOC tips

32K views

Published on: 22/04/2021
How to Make a DIY Foam Sprayer | AUTODOC tips

372K views

Published on: 23/06/2022
#DIY Tips for Fixing Your Car's Air Conditioning Issues | Don't Wait for Costly Repairs!

7K views

Published on: 05/08/2021