Recommended replacement interval for the part category Brake pad set : 30000 km

Important!

This replacement procedure can be used for:
HONDA INTEGRA (DC5) 2.0 (DC5), HONDA INTEGRA (DC5) 2.0 (DC5), HONDA INTEGRA (DC5) 2.0 16V Type-R (DC5) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Brake Pads for INTEGRA (DC5) and other HONDA models

Alternative products

Brake pad set

Replacement: brake pads – HONDA INTEGRA (DC5). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Anti-squeal paste
                    
                      Copper grease 
                    
                      Combination spanner #12
                    
                      Combination spanner #17
                    
                      Drive socket # 12 
                    
                      Drive socket # 17 
                    
                      Wheel impact socket #19
                    
                      Brake caliper wind back tool
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Rubber mallet
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

Replacement: brake pads – HONDA INTEGRA (DC5). AUTODOC recommends:

Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
The replacement procedure is identical for all brake pads on the same axle.
All work should be done with the engine stopped.

Replacement: brake pads – HONDA INTEGRA (DC5). Recommended sequence of steps:

Step 1

Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2

Secure the wheels with chocks.
Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 4

Raise the rear of the car and secure on supports.

Step 5

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. HONDA INTEGRA (DC5)
Step 6

Remove the wheel.
Step 7

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 8

Detach the parking brake cable from the bracket on the brake caliper. Use a drive socket #17. Use a ratchet wrench. Use a crowbar.
Step 9

Unscrew the brake caliper fastening. Use a combination spanner #12. Use a combination spanner #17.
Step 10

Remove the brake caliper.

Replacement: brake pads – HONDA INTEGRA (DC5). Professionals recommend:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 11

Remove the brake pads.

Replacement: brake pads – HONDA INTEGRA (DC5). AUTODOC experts recommend:
Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
Step 12

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: brake pads – HONDA INTEGRA (DC5). After applying the spray, wait a few minutes.
Step 13

Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.

Replacement: brake pads – HONDA INTEGRA (DC5). Tip:
Make sure the disc surface is clean before installing the pads.
Step 14

Install new brake pads.

Replacement: brake pads – HONDA INTEGRA (DC5). AUTODOC experts recommend:
Make sure the pads are installed with linings facing the disc.
Step 15

Treat the brake caliper piston. Use a brake cleaner.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 16

Press in the brake caliper piston. Use brake caliper wind back tool.
Step 17

Install the brake caliper and fix it. Use a combination spanner #12. Use a combination spanner #17. Use a drive socket #12. Use a torque wrench. Tighten it to 23 Nm torque.
Step 18

Install the parking brake cable into the brake caliper bracket. Use a rubber mallet. Use a drive socket #17. Use a ratchet wrench.
Step 19

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 20

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: brake pads – HONDA INTEGRA (DC5). After applying the spray, wait a few minutes.
Step 21

Install the wheel.

Replacement: brake pads – HONDA INTEGRA (DC5). Tip from AUTODOC experts:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 22

Screw in the wheel bolts. Use wheel impact socket #19.
Step 23

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 108 Nm torque.
Step 24

Remove the jacks and chocks.

AUTODOC recommends:
Important! Replacement: brake pads – HONDA INTEGRA (DC5). Check the brake fluid level in the reservoir and top up if necessary.
Step 25

Tighten the brake fluid reservoir cap.

AUTODOC recommends:
HONDA INTEGRA (DC5) – Without starting the engine, press the brake pedal several times until it feels firm.
Step 26

Close the hood.

Replacement: brake pads – HONDA INTEGRA (DC5). AUTODOC recommends:
Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the HONDA Integra III Coupe (DC5) model

Honda DC5 tyre size

How to change engine oil and filter on HONDA Integra III Coupe (DC5) – replacement guide

Free download PDF
1.09 MB
How to change engine oil and filter on Honda Civic 8 – replacement guide

Free download PDF
2.1 MB
How to replace rear brake pads of disc brake on Honda CR-V III

Free download PDF
1.18 MB
How to replace the front brake pads of disc brake on Honda CR-V III

Free download PDF
1.26 MB
How to replace the rear brake disc on Honda CR-V III

Free download PDF
1.33 MB
How to change rear shock absorbers on Honda Civic 8 – replacement guide

Free download PDF
1.91 MB

How to change rear brake pads on HONDA INTEGRA Coupe (DC2, DC4) – replacement guide

Free download PDF
1.46 MB
How to change brake pads on a car – replacement tutorial

Universal

Free download PDF
2.84 MB
How to replace rear brake pads of disc brake on Honda CR-V III

Free download PDF
1.18 MB
How to replace the front brake pads of disc brake on Honda CR-V III

Free download PDF
1.26 MB
How to change rear brake discs on Honda Civic 8 – replacement guide

Free download PDF
2.51 MB
How to change rear brake pads on Honda Civic 8 – replacement guide

Free download PDF
1.74 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Stop Rust Before It Starts: Top 5 Tips for Car Body Protection | AUTODOC Insights

7K views

Published on: 27/07/2023
How to fix your car with AUTODOC CLUB

17K views

Published on: 30/11/2021
3 essential tips for choosing summer tyres | Get ready for warmer weather

4K views

Published on: 18/05/2023
Save Money on Fuel with These Easy Tips | AUTODOC

5K views

Published on: 27/09/2022