How to change rear brake pads on Ford Focus DAW – replacement guide
downloads:
3
Views:
181
0
Users voted – 0
Recommended replacement interval for the part category Brake pad set : 30000km
Important!
This replacement procedure can be used for:
FORD FOCUS (DAW, DBW) 1.4 16V,
FORD FOCUS (DAW, DBW) 1.6 16V,
FORD FOCUS (DAW, DBW) 1.8 16V,
FORD FOCUS (DAW, DBW) 2.0 16V,
FORD FOCUS (DAW, DBW) 1.8 Turbo DI / TDDi,
FORD FOCUS (DAW, DBW) 1.8 DI / TDDi,
FORD FOCUS (DAW, DBW) ST170,
FORD FOCUS (DAW, DBW) 1.8 TDCi,
FORD FOCUS (DAW, DBW) RS
…
View more
The steps may slightly vary depending on the car design.
How to change rear brake pads on FORD FOCUS (DAW) [TUTORIAL AUTODOC]
All the parts you need to replace – Brake Pads for FOCUS (DAW, DBW) and other FORD models
Replacement: brake pads – Ford Focus DAW. AUTODOC experts recommend:
Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
The replacement procedure is identical for all brake pads on the same axle.
Please note: all work on the car – Ford Focus DAW – should be done with the engine switched off.
Carry out replacement in the following order:
Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Pump out any excess brake fluid. Use a hand-operated fluid syringe.
Step 3
Secure the wheels with chocks.
Step 4
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 5
Raise the rear of the car and secure on supports.
Step 6
Unscrew the wheel bolts.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Ford Focus DAW
Step 7
Remove the wheel.
Step 8
Release the parking brake cable. Use water pump pliers.
Step 9
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 10
Unscrew the brake caliper fastening. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.
Step 11
Spread the brake pads. Use a crowbar.
Step 12
Remove the brake caliper.
Replacement: brake pads – Ford Focus DAW. Professionals recommend:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 13
Remove the brake pads.
Replacement: brake pads – Ford Focus DAW. Tip from AUTODOC:
Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
Step 14
Treat the brake caliper piston. Use a nylon cleaning brush. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake pads – Ford Focus DAW. After applying the spray, wait a few minutes.
Step 15
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 16
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
Replacement: brake pads – Ford Focus DAW. Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 17
Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.
Replacement: brake pads – Ford Focus DAW. Professionals recommend:
Make sure the disc surface is clean before installing the pads.
Step 18
Install new brake pads.
Replacement: brake pads – Ford Focus DAW. AUTODOC recommends:
Make sure the pads are installed with linings facing the disc.
Step 19
Install the brake caliper and fix it. Use a combination spanner #15. Use a drive socket #13. Use a torque wrench. Tighten it to 35 nm torque.
Step 20
Install the parking brake cable into the brake caliper bracket. Use water pump pliers.
Step 21
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 22
Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake pads – Ford Focus DAW. After applying the spray, wait a few minutes.
Step 23
Install the wheel.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Ford Focus DAW
Step 24
Screw in the wheel bolts. Use wheel impact socket #19.
Step 25
Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 110 Nm torque.
Step 26
Remove the jacks and chocks.
Replacement: brake pads – Ford Focus DAW. Tip from AUTODOC experts:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 27
Tighten the brake fluid reservoir cap. Close the hood.
Replacement: brake pads – Ford Focus DAW. Professionals recommend:
Without starting the engine, press the brake pedal several times until you feel significant resistance.Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the FORD Focus Mk1 Hatchback (DAW, DBW) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your FORD FOCUS (DAW, DBW)
View more
TOP 5 mistakes during DIY oil change | AUTODOC tips
What to do if the TPMS light is on | AUTODOC tips
What to check when buying a used car | AUTODOC tips