Important!
This replacement procedure can be used for:
AUDI TT Roadster (8J9) 2.0 TFSI, AUDI TT Roadster (8J9) 2.0 TFSI quattro, AUDI TT Roadster (8J9) 2.5 RS quattro, AUDI TT Roadster (8J9) 2.0 TFSI, AUDI TT Roadster (8J9) 3.2 V6 quattro, AUDI TT Roadster (8J9) 2.0 TTS quattro, AUDI TT Roadster (8J9) 1.8 TFSI, AUDI TT Roadster (8J9) 2.0 TDI quattro, AUDI TT Roadster (8J9) 2.0 TTS quattro, AUDI TT Roadster (8J9) 2.0 TFSI quattro, AUDI TT Roadster (8J9) 2.5 RS quattro View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Anti Roll Bar Links for TT Roadster (8J9) and other AUDI models
Alternative products
How to change Anti-roll bar link on Audi TT Roadster 2.0 TFSI – step-by-step instructions for straightforward car repair Anti-roll bar link
Tools
Replacement: anti roll bar links – AUDI TT Roadster (8J9). List of the tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #14
Combination spanner #16
HEX bit No.H5.
XZN socket bit # 6
Drive socket # 14
Wheel impact socket #17
Ratchet wrench
Torque wrench
Hydraulic transmission jack
Wheel chock
Replacement: anti roll bar links – AUDI TT Roadster (8J9). AUTODOC recommends:
  • Replace the stabiliser links on AUDI TT Roadster (8J9) in pairs.
  • The replacement procedure is identical for both stabiliser links on the same axle.
  • All work should be done with the engine stopped.
Replacement: anti roll bar links – AUDI TT Roadster (8J9). Use the following procedure:
  1. Step 1
    How to change Anti Roll Bar Links on Audi TT Roadster 2007 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 2
    How to replace AUDI TT Roadster (8J9) 2.0 TFSI 2008 Anti Roll Bar Links - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  3. Step 3
    Raise the rear of the car and secure on supports.
    Step 4
    Audi TT Roadster 1.8 TFSI 2009 Anti Roll Bar Links replacement: free workshop manuals
    Unscrew the wheel bolts.
    Replacement: anti roll bar links – AUDI TT Roadster (8J9). Tip:
    To avoid injury, hold up the wheel when unscrewing the bolts.
  4. Step 5
    Changing Anti Roll Bar Links on AUDI TT Roadster (8J9) 2.0 TDI quattro 2010 by yourself
    Remove the wheel.
  5. Step 6
    How to remove AUDI TT 3.2 V6 quattro 2011 Anti Roll Bar Links - online easy-to-follow instructions
    Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
  6. Step 7
    How to replace Anti Roll Bar Links on AUDI TT Roadster (8J9) 2012: download PDF manuals and video instructions
    Unscrew the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
  7. Step 8
    How hard is it to do yourself: Anti Roll Bar Links replacement on Audi TT Roadster 2.0 TFSI quattro 2013 - download illustrated guide
    Unscrew the fasteners connecting the stabiliser link to the stabiliser bar. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
  8. Step 9
    Need to know how to renew Anti Roll Bar Links on AUDI TT 2014? This free workshop manual will help you to do it yourself
    Remove the stabilizer rod.
    Replacement: anti roll bar links – AUDI TT Roadster (8J9). Tip from AUTODOC experts:
    Examine stabiliser bushes. Replace them if needed.
  9. Step 10
    Changing of Anti Roll Bar Links on Audi TT Roadster 2007 won't be an issue if you follow this illustrated step-by-step guide
    Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
  10. Step 11
    AUDI TT 1.8 TFSI Anti Roll Bar Links replacement: online guides and video tutorials
    Ιnstall the transverse stabilizer link.
  11. Step 12
    Replacing Anti Roll Bar Links on Audi TT Roadster 2009 2.0 TFSI by yourself
    Tighten the stabiliser link fastener. Use a combination spanner #14. Use HEX No.H5. Use a ratchet wrench.
  12. Step 13
    TT Roadster (8J9) 3.2 V6 quattro 2010 Anti Roll Bar Links DIY replacement workshop manual
    Tighten the fastener connecting the stabilizer bar with the control arm. Use a drive socket #14. Use a torque wrench. Tighten it to 45 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?

Find out which tyre and wheel sizes are compatible with the AUDI TT Roadster (8J9) model

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY AUDI TT Roadster (8J9) Anti Roll Bar Links replacement - online guide
Tips & tricks for your AUDI TT Roadster (8J9)
View more
  • How to change Drop links on AUDI TT Roadster (8J9) 2.0 TTS quattro - replacement tricks
    5 mistakes made when washing the engine | AUTODOC tips
  • Changing Stabilizer link Audi TT Roadster 2.0 TFSI - Replacement Tips
    DIY brake caliper restoration | AUTODOC tips
  • Maintenance Hacks - AUDI TT Roadster (8J9) 1.8 TFSI Sway bar link replacement guide
    5 Ways You’re Scrubbing Your Car Wrong | AUTODOC Tips
  • Replace Drop link on Audi TT Roadster - free video tips
    DIY rear axle restoration | Drivetrain restoration – Part 2

Professional manuals for the most common AUDI models

Autodoc CLUB App icon
Time to replace parts? Get even better deals in our Shop app.
AUDI TT Roadster (8J9) Anti Roll Bar Links replace by yourself - Scan QR-code and download AUTODOC CLUB app
SCAN ME