Disclaimer
How to change lambda sensor on VW Bora Saloon (1J2) – replacement guide
downloads:
7
Views:
162
Recommended replacement interval for the part category Lambda sensor : 100000 km
Important!
This replacement procedure can be used for:
VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.0, VW Bora Saloon (1J2) 1.4 16V, VW Bora Saloon (1J2) 2.8 V6 4motion, VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.3 V5, VW Bora Saloon (1J2) 2.3 V5 4motion, VW Bora Saloon (1J2) 1.8 T, VW Bora Saloon (1J2) 2.0 4motion, VW Bora Saloon (1J2) 1.8 T … View more
The steps may slightly vary depending on the car design.
VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.0, VW Bora Saloon (1J2) 1.4 16V, VW Bora Saloon (1J2) 2.8 V6 4motion, VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.3 V5, VW Bora Saloon (1J2) 2.3 V5 4motion, VW Bora Saloon (1J2) 1.8 T, VW Bora Saloon (1J2) 2.0 4motion, VW Bora Saloon (1J2) 1.8 T … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Lambda Sensor for Bora Saloon (1J2) and other VW models
Alternative products
Lambda sensor
Electronic spray
High-temperature ceramic grease
Torque wrench
Drive socket # 10
22-mm oxygen sensor socket
Ratchet wrench
Thread tap
Fender cover
Replacement: lambda sensor – VW BORA (1J2). AUTODOC experts recommend:
- After replacing the oxygen sensor, clear the trouble code from the electronic control unit and let the ECU adapt itself to the new sensor.
- Before getting down to work, start the engine and let it warm up to operating temperature.
- Please note: all work on the car – VW BORA (1J2) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Lift the car using a jack or place it over an inspection pit.Step 4
Unscrew the fasteners of the oxygen sensor housing cover. Use a drive socket #10. Use a ratchet wrench. - Step 5
Remove the oxygen sensor housing cover. - Step 6
Detach the oxygen sensor connector. - Step 7
Unscrew the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a ratchet wrench. - Step 8
Remove the oxygen sensor. - Step 9
Cut the thread for the new oxygen sensor. Use a thread tap. Use a ratchet wrench. - Step 10Treat the oxygen sensor. Use high-temperature ceramic grease.Step 11
Install the new oxygen sensor. - Step 12
Tighten the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a torque wrench. Tighten it to 37 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Bora Saloon (1J2) model
Popular maintenance tutorials for VW Bora 1j2
Free download PDF
1.43 MB
Free download PDF1.2 MB
Free download PDF972.8 KB
Free download PDF1.82 MB
Free download PDF1.49 MB
Free download PDF2.3 MB
Complete guides for changing the Oxygen sensor on different VW BORA models
Free download PDF890.88 KB
Free download PDF972.8 KB
Free download PDF1 MB
Free download PDF1.29 MB
Free download PDF1.36 MB
Free download PDF890.88 KB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Bora Saloon (1J2)
View more
Cold starts | 5 mistakes that wreck your car
How to Fix a Squealing Belt: Causes & Solutions | AUTODOC Expert Tips
Motorcycle fuel tank restoration
DIY engine block coffee table
Most commonly replaced car parts on VW BORA
Time to replace parts? Get even better deals in our Shop app.
SCAN ME