Important!

This replacement procedure can be used for:
RENAULT MEGANE II Saloon (LM0/1_) 1.6 Hi-Flex (LM2E, LM2M, LM24), RENAULT MEGANE II Saloon (LM0/1_) 1.4, RENAULT MEGANE II Saloon (LM0/1_) 1.6, RENAULT MEGANE II Saloon (LM0/1_) 2.0, RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM0F, LM0T, LM2B), RENAULT MEGANE II Saloon (LM0/1_) 1.9 dCi (LM0G, LM1G, LM2C), RENAULT MEGANE II Saloon (LM0/1_) 1.9 dCi, RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM02, LM13, LM2A), RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM1F), RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM1E), RENAULT MEGANE II Saloon (LM0/1_) 1.9 dCi, RENAULT MEGANE II Saloon (LM0/1_) 1.9 dCi (LM14, LM1D), RENAULT MEGANE II Saloon (LM0/1_) 2.0 dCi, RENAULT MEGANE II Saloon (LM0/1_) 1.6 16V (LM1R, LM0C), RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM16), RENAULT MEGANE II Saloon (LM0/1_) 1.6, RENAULT MEGANE II Saloon (LM0/1_) 1.6, RENAULT MEGANE II Saloon (LM0/1_) 1.9 dCi, RENAULT MEGANE II Saloon (LM0/1_) 1.6, RENAULT MEGANE II Saloon (LM0/1_) 2.0 … View more

The steps may slightly vary depending on the car design.

How to change front suspension arm / front control arm on RENAULT MEGANE 2 (LM) [TUTORIAL AUTODOC]

Alternative products

Suspension arm

Replacement: front lower arm – Renault Megane 2. Tools you might need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Combination spanner #16
                    
                      Combination spanner #18
                    
                      Drive socket # 12 
                    
                      Drive socket # 13 
                    
                      Drive socket # 16 
                    
                      Drive socket # E16 
                    
                      Drive socket # 18 
                    
                      Torx bit T20
                    
                      Wheel impact socket #19
                    
                      Shock absorber socket
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Clip removal tool
                    
                      Pin punch
                    
                      Hammer
                    
                      Crow bar
                    
                      Rubber mallet
                    
                      Hydraulic transmission jack
                    
                      Fender cover
                    
                      Wheel chock

Buy tools

Replacement: front lower arm – Renault Megane 2. AUTODOC experts recommend:

The replacement procedure is identical for the left and right lower control arms.
All work should be done with the engine stopped.

Replacement: front lower arm – Renault Megane 2. Use the following procedure:

Step 1

Open the bonnet.
Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3

Secure the wheels with chocks.
Step 4

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 5

Raise the front of the car and secure on supports.
Step 6

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. Renault Megane 2
Step 7

Remove the wheel.
Step 8

Remove the lower sound insulation. Use a drive socket #12.
Step 9

Unscrew and remove the wheel arch cover fasteners. Use Torx T20. Use a clip removal tool.
Step 10

Remove the wheel arch cover.
Step 11

Clean the fasteners of the bumper reinforcement bar and of its bracket. Use a wire brush. Use WD-40 spray.

Replacement: front lower arm – Renault Megane 2. AUTODOC experts recommend:
After applying the spray, wait a few minutes.Wear protective goggles.
Step 12

Unscrew the fasteners of the bumper reinforcement bar bracket. Use a drive socket #13.
Step 13

Unscrew the fasteners connecting the bumper reinforcement bar to the subframe. Use a drive socket #13. Use a ratchet wrench.
Step 14

Support the lower radiator support to prevent it from falling when removing the bumper reinforcement bar. Use a hydraulic transmission jack.
Step 15

Loosen the fastener connecting the bumper reinforcement bar to the lower radiator support. Use a drive socket #18. Use a ratchet wrench.
Step 16

Detach and pull aside the bumper reinforcement bar. Use a crowbar.
Step 17

Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 18

Clean the fasteners connecting the control arm to the subframe. Use a wire brush. Use WD-40 spray.
Step 19

Detach the ABS sensor wiring from the suspension control arm. Use a clip removal tool.
Step 20

Unscrew the ball joint fastening to the steering knuckle. Use a drive socket #16. Use a combination spanner #18. Use a ratchet wrench.
Step 21

Remove the fastening bolt. Use a hammer. Use a pin punch.
Step 22

Unscrew the front arm fastener. Use a drive socket #E16. Use a combination spanner #18. Use a ratchet wrench.
Step 23

Remove the fastening bolt. Use a crowbar.
Step 24

Unscrew the rear arm fastener. Use a drive socket #18. Use a combination spanner #18. Use a ratchet wrench.
Step 25

Release the fastener connecting the ball joint to the steering knuckle. Use a special drive socket to remove the shock absorber.
Step 26

Disconnect the ball joint from the steering knuckle. Use a crowbar.
Step 27

Remove the arm. Use a crowbar.
Step 28

Clean the mounting seats and the thread of the suspension arm. Use a wire brush.
Step 29

Install a new arm.
Step 30

Connect the ball joint to the steering knuckle.
Step 31

Install the control arm fasteners.
Step 32

Screw the rear arm fastener. Use a drive socket #18.
Step 33

Install the front fastener of the arm. Use a crowbar. Use a rubber mallet.
Step 34

Screw the front arm fastener. Use a drive socket #E16. Use a combination spanner #18. Use a ratchet wrench.
Step 35

Install the bumper reinforcement bar. Use a crowbar.
Step 36

Screw in the fastener connecting the bumper reinforcement bar to the lower radiator support.
Step 37

Screw in the fastener connecting the bumper reinforcement bar to the subframe.
Step 38

Remove the support from under the lower radiator support.

AUTODOC recommends:
Replacement: front lower arm – Renault Megane 2. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 39

Support the arm. Use a hydraulic transmission jack.
Step 40

Tighten the rear fastener connecting the arm to the body subframe. Use a drive socket #18. Use a combination spanner #18. Use a torque wrench. Tighten it to 105 nm torque.
Step 41

Tighten the front fastener connecting the control arm to the subframe. Use a combination spanner #16. Use a combination spanner #18. Use a torque wrench. Tighten it to 105 nm torque.
Step 42

Tighten the ball joint fastener. Use a drive socket #16. Use a combination spanner #18. Use a torque wrench. Tighten it to 62 nm torque.
Step 43

Remove the support from under the arm.

Replacement: front lower arm – Renault Megane 2. Professionals recommend:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 44

Tighten the fastener connecting the bumper reinforcement bar to the subframe. Use a drive socket #13. Use a ratchet wrench.
Step 45

Tighten the fastener connecting the bumper reinforcement bar to the lower radiator support. Use a drive socket #18. Use a torque wrench. Tighten it to 75 nm torque.
Step 46

Treat all joints of the arm. Use copper grease.
Step 47

Screw in the fastener of the bumper reinforcement bar bracket. Use a drive socket #13.
Step 48

Connect the ABS sensor wiring.
Step 49

Install the wheel arch cover to its mounting seat.
Step 50

Install and tighten the wheel arch cover fasteners. Use Torx T20.
Step 51

Install the lower sound insulation.
Step 52

Screw in the fasteners of the lower sound insulation. Use a drive socket #12.
Step 53

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 54

Install the wheel.

Replacement: front lower arm – Renault Megane 2. Tip from AUTODOC experts:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 55

Screw in the wheel bolts. Use wheel impact socket #19.
Step 56

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 nm torque.
Step 57

Remove the jacks and chocks.
Step 58

Remove the fender protection cover.
Step 59

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the RENAULT Megane II Saloon (LM) model

RENAULT MEGANE II Saloon (LM0/1_) tyre size

How to change rear wheel bearing on Renault Megane 2 – replacement guide

Free download PDF
2.33 MB
How to change front strut mount on Renault Megane 2 – replacement guide

Free download PDF
3.43 MB
How to change front anti roll bar links on Renault Megane 2 – replacement guide

Free download PDF
1.94 MB
How to change front wheel bearing on RENAULT MEGANE II Saloon (LM0/1_) – replacement guide

Free download PDF
4.01 MB
How to change rear brake pads on Renault Megane 2 – replacement guide

Free download PDF
2.49 MB
How to change front brake pads on RENAULT MEGANE II Saloon (LM0/1_) – replacement guide

Free download PDF
1.51 MB

How to change front lower arm on RENAULT MEGANE II (BM0/1_, CM0/1_) – replacement guide

Free download PDF
2.95 MB
How to change front lower arm on RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) – replacement guide

Free download PDF
2.95 MB
How to change front lower arm on RENAULT MEGANE II Estate (KM0/1_) – replacement guide

Free download PDF
2.95 MB
How to change front lower arm on RENAULT MEGANE II Box Body / Estate (KM_) – replacement guide

Free download PDF
2.94 MB
How to change front lower arm on RENAULT Megane II Box Body / Hatchback (KM0/2_) – replacement guide

Free download PDF
2.94 MB
How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to get your motorcycle ready for spring

3K views

Published on: 22/05/2025
Regain Your Confidence on the Road: Easy Headlight Restoration Tips

10K views

Published on: 04/07/2024
DIY vehicle AC compressor restoration

763K views

Published on: 28/11/2024
The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips

9K views

Published on: 08/12/2020