How to change front strut mount on Renault Megane 2 – replacement guide
downloads:
5
Views:
137
0
Users voted – 0
Important!
This replacement procedure can be used for:
RENAULT MEGANE II Saloon (LM0/1_) 1.4,
RENAULT MEGANE II Saloon (LM0/1_) 1.6,
RENAULT MEGANE II Saloon (LM0/1_) 2.0,
RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM0F, LM0T, LM2B),
RENAULT MEGANE II Saloon (LM0/1_) 1.9 dCi (LM0G, LM1G, LM2C),
RENAULT MEGANE II Saloon (LM0/1_) 1.9 dCi,
RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM02, LM13, LM2A),
RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM1F),
RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM1E),
RENAULT MEGANE II Saloon (LM0/1_) 1.9 dCi,
RENAULT MEGANE II Saloon (LM0/1_) 2.0 dCi,
RENAULT MEGANE II Saloon (LM0/1_) 1.6 16V (LM1R, LM0C),
RENAULT MEGANE II Saloon (LM0/1_) 1.5 dCi (LM16)
…
View more
The steps may slightly vary depending on the car design.
How to change front strut mount / top munt RENAULT MEGANE 2 (LM) [TUTORIAL AUTODOC]
All the parts you need to replace – Strut Mount for MEGANE II Saloon (LM0/1_) and other RENAULT models
Replacement: strut mount – Renault Megane 2. AUTODOC recommends:
All mounts of the front shock struts should be replaced simultaneously.
The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
Be sure to replace all self-locking nuts and bolts during installation.
All work should be done with the engine stopped.
Replacement: strut mount – Renault Megane 2. Recommended sequence of steps:
Step 1
Open the bonnet.
Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3
Remove the retainers of the shock strut mount cap. Use a clip removal tool.
Step 4
Raise a little the shock strut mount cap. Treat the fasteners of the shock strut mount. Use WD-40 spray.
Step 5
Loosen the upper fastener of the shock strut mount. Use a drive socket #13. Use a ratchet wrench.
Step 6
Secure the wheels with chocks.
Step 7
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 8
Raise the front of the car and secure on supports.
Step 9
Unscrew the wheel bolts.
Replacement: strut mount – Renault Megane 2. Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 10
Remove the wheel.
Step 11
Disconnect the wiring and the brake hose from the bracket on the shock strut. Use a crowbar.
Step 12
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 13
Unscrew the nut and remove the stabilizer rod from the shock strut. Use HEX No.H6. Use a combination spanner #17.
Step 14
Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 15
Unscrew the lower fastener of the shock absorber strut. Use a drive socket #19. Use a tap wrench.
Step 16
Remove the fastening bolt.
Replacement: strut mount – Renault Megane 2. AUTODOC experts recommend:
Make sure that the steering knuckle is supported.
Step 17
Disconnect the steering knuckle from the shock absorber strut. Use a hammer. Use a flat metal-working chisel.
Step 18
Unscrew the upper fastening of the shock absorber strut. Use a drive socket #13. Use a ratchet wrench.
Replacement: strut mount – Renault Megane 2. Professionals recommend:
To avoid injuries, hold the shock strut when undoing the fastening bolts.
Step 19
Remove the suspension strut.
Step 20
Set the shock absorber strut on the spring compressor tool.
Replacement: strut mount – Renault Megane 2. Tip from AUTODOC experts:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 21
Compress the spring.
Step 22
Remove the strut piston rod nut. Use HEX No.H6. Use a combination spanner #18. Use a ratchet wrench.
Step 23
Remove the top strut mount.
Step 24
Install a new top shock strut mount.
Step 25
Tighten the shock strut piston rod nut. Use HEX No.H6. Use a combination spanner #18. Use a torque wrench. Tighten it to 62 Nm torque.
Replacement: strut mount – Renault Megane 2. Tip from AUTODOC:
Check to make sure the spring is positioned correctly. Avoid its misalignment. Important! Be sure to use new fasteners.
Step 26
Decompress the spring.
Step 27
Remove the assembled shock strut.
Step 28
Install the shock strut into the wheel arch.
Step 29
Secure the upper fasteners of the shock strut (3 pieces). Do not tighten it.
AUTODOC recommends:
Important! Hold the suspension strut while screwing in the fastening bolts. Renault Megane 2
Step 30
Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 31
Fix the shock absorber strut on the steering knuckle.
Step 32
Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 33
Install and tighten a new bolt of the steering knuckle. Use a drive socket #19. Use a combination spanner #19. Use a torque wrench. Tighten it to 105 Nm torque.
Step 34
Remove the support from under the steering knuckle.
AUTODOC recommends:
Replacement: strut mount – Renault Megane 2. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 35
Connect the fastener of the ABS sensor cable to the shock absorber strut. Fasten the brake hose on the strut.
Step 36
Secure the stabilizer link on the suspension strut. Use HEX No.H6. Use a combination spanner #17. Use a torque wrench. Tighten it to 44 Nm torque.
Step 37
Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 38
Install the wheel.
Replacement: strut mount – Renault Megane 2. AUTODOC experts recommend:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 39
Screw in the wheel bolts. Use wheel impact socket #19.
Step 40
Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 Nm torque.
Step 41
Tighten the shock strut top mount. Use a drive socket #13. Use a torque wrench. Tighten it to 21 Nm torque.
Step 42
Install the shock strut mount cap.
Step 43
Install the retainers of the shock strut mount cap.
Step 44
Remove the fender protection cover.
Step 45
Close the hood.
Step 46
Remove the jacks and chocks.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Megane II Saloon (LM) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your RENAULT MEGANE II Saloon (LM0/1_)
View more
4 reasons why your CHECK ENGINE light is on | AUTODOC tips
5 causes of turbocharger failure and how to avoid them | AUTODOC tips
How to easily repair a punctured tyre | AUTODOC tips
How to shine your tyres | AUTODOC tips
Most commonly replaced car parts on RENAULT MEGANE