Disclaimer
How to change front lower arm on RENAULT MEGANE II Box Body / Estate (KM_) – replacement guide
downloads:
1
Views:
18
Important!
This replacement procedure can be used for:
RENAULT MEGANE II Box Body / Estate (KM_) 1.5 dCi (KM1E), RENAULT MEGANE II Box Body / Estate (KM_) 1.5 dCi (KM0F), RENAULT MEGANE II Box Body / Estate (KM_) 1.5 dCi (KM02), RENAULT MEGANE II Box Body / Estate (KM_) 1.5 dCi (KM1F) … View more
The steps may slightly vary depending on the car design.
RENAULT MEGANE II Box Body / Estate (KM_) 1.5 dCi (KM1E), RENAULT MEGANE II Box Body / Estate (KM_) 1.5 dCi (KM0F), RENAULT MEGANE II Box Body / Estate (KM_) 1.5 dCi (KM02), RENAULT MEGANE II Box Body / Estate (KM_) 1.5 dCi (KM1F) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Control Arm for MEGANE II Box Body / Estate (KM_) and other RENAULT models
Alternative products

Wire brush
WD-40 spray
Copper grease
Combination spanner #16
Combination spanner #18
Drive socket # 12
Drive socket # 13
Drive socket # 16
Drive socket # E16
Drive socket # 18
Torx bit T20
Wheel impact socket #19
Shock absorber socket
Ratchet wrench
Torque wrench
Clip removal tool
Pin punch
Hammer
Crow bar
Rubber mallet
Hydraulic transmission jack
Fender cover
Wheel chock
Replacement: front lower arm – RENAULT MEGANE II Box Body / Estate (KM_). AUTODOC experts recommend:
- The replacement procedure is identical for the left and right lower control arms.
- All work should be done with the engine stopped.
Replacement: front lower arm – RENAULT MEGANE II Box Body / Estate (KM_). Use the following procedure:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Secure the wheels with chocks. - Step 4
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 5Raise the front of the car and secure on supports.Step 6
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. RENAULT MEGANE II Box Body / Estate (KM_) - Step 7
Remove the wheel. - Step 8
Remove the lower sound insulation. Use a drive socket #12. - Step 9
Unscrew and remove the wheel arch cover fasteners. Use Torx T20. Use a clip removal tool. - Step 10
Remove the wheel arch cover. - Step 11
Clean the fasteners of the bumper reinforcement bar and of its bracket. Use a wire brush. Use WD-40 spray.Replacement: front lower arm – RENAULT MEGANE II Box Body / Estate (KM_). AUTODOC experts recommend:After applying the spray, wait a few minutes.Wear protective goggles. - Step 12
Unscrew the fasteners of the bumper reinforcement bar bracket. Use a drive socket #13. - Step 13
Unscrew the fasteners connecting the bumper reinforcement bar to the subframe. Use a drive socket #13. Use a ratchet wrench. - Step 14
Support the lower radiator support to prevent it from falling when removing the bumper reinforcement bar. Use a hydraulic transmission jack. - Step 15
Loosen the fastener connecting the bumper reinforcement bar to the lower radiator support. Use a drive socket #18. Use a ratchet wrench. - Step 16
Detach and pull aside the bumper reinforcement bar. Use a crowbar. - Step 17
Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray. - Step 18
Clean the fasteners connecting the control arm to the subframe. Use a wire brush. Use WD-40 spray. - Step 19
Detach the ABS sensor wiring from the suspension control arm. Use a clip removal tool. - Step 20
Unscrew the ball joint fastening to the steering knuckle. Use a drive socket #16. Use a combination spanner #18. Use a ratchet wrench. - Step 21
Remove the fastening bolt. Use a hammer. Use a pin punch. - Step 22
Unscrew the front arm fastener. Use a drive socket #E16. Use a combination spanner #18. Use a ratchet wrench. - Step 23
Remove the fastening bolt. Use a crowbar. - Step 24
Unscrew the rear arm fastener. Use a drive socket #18. Use a combination spanner #18. Use a ratchet wrench. - Step 25
Release the fastener connecting the ball joint to the steering knuckle. Use a special drive socket to remove the shock absorber. - Step 26
Disconnect the ball joint from the steering knuckle. Use a crowbar. - Step 27
Remove the arm. Use a crowbar. - Step 28
Clean the mounting seats and the thread of the suspension arm. Use a wire brush. - Step 29
Install a new arm. - Step 30
Connect the ball joint to the steering knuckle. - Step 31
Install the control arm fasteners. - Step 32
Screw the rear arm fastener. Use a drive socket #18. - Step 33
Install the front fastener of the arm. Use a crowbar. Use a rubber mallet. - Step 34
Screw the front arm fastener. Use a drive socket #E16. Use a combination spanner #18. Use a ratchet wrench. - Step 35
Install the bumper reinforcement bar. Use a crowbar.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Megane II Box Body / Estate (KM_) model
Popular maintenance tutorials for Renault Megane II Estate
Complete guides for changing the Control arm on different RENAULT MEGANE models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT MEGANE II Box Body / Estate (KM_)
View more
DIY car soundproofing | AUTODOC tips
Motorcycle fuel tank restoration
5 Essential Tips to Prepare Your Car for Winter | AUTODOC tips
#DIY Tips for Fixing Your Car's Air Conditioning Issues | Don't Wait for Costly Repairs!
Most commonly replaced car parts on RENAULT MEGANE
Time to replace parts? Get even better deals in our Shop app.

SCAN ME







































