Recommended replacement interval for the part category Brake Disc : 50000 km

Important!

This replacement procedure can be used for:
BMW 3 Convertible (E30) 318 i, HONDA CR-V II (RD_) 2.2 CTDi (RD9), HONDA CIVIC VIII Hatchback (FN, FK) 2.2 CTDi (FK3)

The steps may slightly vary depending on the car design.

How to change front brake discs and front brake pads on HONDA CR-V 2 TUTORIAL | AUTODOC

Replacement: brake discs – Honda CR-V II. List of the tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Drive socket # 12
                      
                        Drive socket # 17
                      
                        Wheel impact socket #19
                      
                        Brake caliper wind back tool
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Phillips screwdriver
                      
                        Impact screwdriver
                      
                        Hammer
                      
                        Crow bar
                      
                        Wheel chock

All the parts you need to replace – Brake Discs for CR-V II (RD_) and other HONDA models

    HONDA CR-V II (RD_) 2.2 CTDi (RD9)
  
    HONDA CIVIC VIII Hatchback (FN, FK) 2.2 CTDi (FK3)
  
    BMW 3 Convertible (E30) 318 i

AUTODOC recommends:

Replace the brake disks on the car Honda CR-V II in complete set for each axis. Regardless of the state of components. This will ensure even braking.
The replacement procedure is identical for both brake disks on the same axle.
When changing the brake discs, always replace the brake pads.
Please note: all work on the car – Honda CR-V II – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet.Unscrew the brake fluid reservoir cap.
Step 2

Secure the wheels with chocks.
Step 3

Loosen the wheel mounting bolts.Use wheel impact socket #19.
Step 4

Raise the front of the car and secure on supports.
Step 5

Unscrew the wheel bolts.

AUTODOC recommends:

Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Honda CR-V II
Step 6

Remove the wheel.
Step 7

Clean the brake caliper fasteners. Use a wire brush.Use WD-40 spray.
Step 8

Unscrew the brake caliper fastening.Use a drive socket #12.Use a ratchet wrench.
Step 9

Spread the brake pads.Use a crowbar.
Step 10

Remove the brake caliper.

Replacement: brake discs – Honda CR-V II. Tip:

Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 11

Remove the retaining springs of the brake pads.
Step 12

Remove the brake pads.Use a crowbar.
Step 13

Clean the brake caliper bracket fasteners. Use a wire brush.Use WD-40 spray.
Step 14

Unscrew the caliper bracket fastening.Use a drive socket #17.Use a ratchet wrench.
Step 15

Remove the caliper bracket.
Step 16

Clean the brake disc fasteners.Use a wire brush.Use WD-40 spray.
Step 17

Unscrew the brake disc fastening.Use an impact screwdriver.Use a hammer.
Step 18

Remove the brake disc.
Step 19

Clean the hub.Use a wire brush.Treat the contacting surface.Use copper grease.
Step 20

Install the brake disc.
Step 21

Tighten the brake disc fastening.Use a Phillips screwdriver.Use a torque wrench.Tighten it to 9 Nm torque.
Step 22

Clean the brake caliper bracket from dirt and dust.Use a wire brush.Use a brake cleaner.

AUTODOC recommends:

Replacement: brake discs – Honda CR-V II. After applying the spray, wait a few minutes.
Step 23

Install the brake caliper bracket.
Step 24

Tighten the brake caliper bracket.Use a drive socket #17.Use a torque wrench.Tighten it to 75 Nm torque.
Step 25

Install the brake pads.
Step 26

Install the retaining springs of the brake pads.
Step 27

Treat the brake caliper piston.Use a brake cleaner.

Replacement: brake discs – Honda CR-V II. Tip from AUTODOC experts:

After applying the spray, wait a few minutes.
Step 28

Press in the brake caliper piston.Use brake caliper wind back tool.
Step 29.1

Install the brake caliper and fix it.

Step 29.2

Use a drive socket #12.Use a torque wrench.Tighten it to 35 Nm torque.
Step 30

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 31

Clean the brake disk surface.Use a brake cleaner.

AUTODOC recommends:

Replacement: brake discs – Honda CR-V II. After applying the spray, wait a few minutes.
Step 32

Install the wheel.

AUTODOC recommends:

Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Honda CR-V II
Step 33

Screw in the wheel bolts.Use wheel impact socket #19.
Step 34

Lower the car and working in a cross order, tighten the wheel bolts.Use wheel impact socket #19.Use a torque wrench.Tighten it to 120 Nm torque.
Step 35

Remove the jacks and chocks.

Replacement: brake discs – Honda CR-V II. AUTODOC experts recommend:

Check the brake fluid level in the expansion tank and refill if necessary.
Step 36

Tighten the brake fluid reservoir cap.Close the hood.

Replacement: brake discs – Honda CR-V II. Tip from AUTODOC experts:

Without starting the engine, press the brake pedal several times until you feel significant resistance.

Comment

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

How to replace rear brake pads of disc brake on Honda CR-V III

Free download PDF

1.18 MB
How to replace the rear brake disc on Honda CR-V III

Free download PDF

1.33 MB
How to replace the front brake pads of disc brake on Honda CR-V III

Free download PDF

1.26 MB
How to replace the rear hub bearing on Honda CR-V III

Free download PDF

1.54 MB
How to replace a front suspension ball joint on Honda CR-V III

Free download PDF

1.18 MB
How to replace the tie rod end on Honda CR-V III

Free download PDF

1.13 MB
How to replace the front brake disc on Honda CR-V III

Free download PDF

1.16 MB
How to change rear brake pads on Honda CR-V II – replacement guide

Free download PDF

6.41 MB
How to change front anti roll bar links on Honda CR-V II – replacement guide

Free download PDF

5.28 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Tips & tricks for your HONDA CR-V II (RD_)

How to paint a brake caliper | AUTODOC tips

5K views

Published on: 08/04/2021
How to easily repair a punctured tyre | AUTODOC tips

2K views

Published on: 25/02/2021
What causes engine misfire? | AUTODOC

2K views

Published on: 10/07/2020
How to change automatic transmission fluid | AUTODOC tips

3K views

Published on: 16/09/2020