Important!

This replacement procedure can be used for:
SEAT Toledo II Saloon (1M2) 1.6, SEAT Toledo II Saloon (1M2) 1.8 20V, SEAT Toledo II Saloon (1M2) 2.3 V5, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.4 16V, SEAT Toledo II Saloon (1M2) 1.6 16V, SEAT Toledo II Saloon (1M2) 2.3 V5 20V, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.8 20VT … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Suspension Ball Joint for Toledo II Saloon (1M2) and other SEAT models

Alternative products

Ball Joint

Replacement: ball joint – SEAT TOLEDO II (1M2). Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner
                    
                      Copper grease
                    
                      High-temperature ceramic grease
                    
                      Torque wrench
                    
                      Drive socket # 13
                    
                      Drive socket # 16
                    
                      Drive socket # 30
                    
                      Combination spanner #18
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Crow bar
                    
                      Ball joint puller
                    
                      Rubber mallet
                    
                      Pin punch
                    
                      Wheel chock

Buy tools

Replacement: ball joint – SEAT TOLEDO II (1M2). Tip:

The replacement procedure is identical for the left and right ball joints.
All work should be done with the engine stopped.

Replacement: ball joint – SEAT TOLEDO II (1M2). Take the following steps:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. SEAT TOLEDO II (1M2)
Step 5

Remove the wheel.
Step 6

Clean the ball joint fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #18.
Step 8

Loosen the fastener of the driveshaft. Use a drive socket #30. Use a ratchet wrench.
Step 9

Remove the drive shaft. Use a pin punch. Use a rubber mallet.
Step 10

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.

Step 11

Unscrew the fastener connecting the stabilizer link to the control arm. Use a drive socket #16. Use a ratchet wrench.
Step 12

Remove the fastening bolt.

Step 13

Disconnect the ball joint from the steering knuckle. Use a ball joint puller.
Step 14

Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #13. Use a ratchet wrench.
Step 15

Remove the fastening bolts.

Step 16

Remove the ball joint.
Step 17

Clean the ball joint mounting seat. Use a wire brush. Use WD-40 spray.
Step 18

Install a new ball joint.

AUTODOC recommends:
Do not damage the ball joint cover.
Step 19

Attach the ball joint to the control arm.

Step 20

Install the fastening bolts.

Step 21

Tighten the fasteners connecting the ball joint to the control arm. Use a drive socket #13. Use a torque wrench. Tighten it to 20 Nm torque.+90°
Step 22

Connect the ball joint to the steering knuckle. Use a crowbar.

Step 23

Tighten the ball joint fastener. Use a combination spanner #18. Use a torque wrench. Tighten it to 20 Nm torque.+90°
Step 24

Install the rod fastening to the stabilizer and tighten it. Use a drive socket #16. Use a torque wrench. Tighten it to 15 Nm torque.+90°
Step 25

Mount the drive shaft into the wheel hub.

Step 26

Tighten the drive shaft nut. Use a drive socket #30. Use a torque wrench. Tighten it to 225 Nm torque.
Step 27

Treat the fasteners of the ball joint. Treat all joints of the stabiliser link. Use copper grease.
Step 28

Treat the surface where the brake disc contacts the wheel rim. Use high-temperature ceramic grease.
Step 29

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: ball joint – SEAT TOLEDO II (1M2). After applying the spray, wait a few minutes.
Step 30

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. SEAT TOLEDO II (1M2)
Step 31

Screw in the wheel bolts. Use wheel impact socket #17.
Step 32

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 nm torque.
Step 33

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the SEAT Toledo II Saloon (1M2) model

Seat Toledo 1m tyre size

How to change front strut mount on SEAT Toledo II Saloon (1M2) – replacement guide

Free download PDF
2.79 MB
How to change front lower arm on SEAT Toledo II Saloon (1M2) – replacement guide

Free download PDF
1.96 MB
How to change track rod end on SEAT Toledo II Saloon (1M2) – replacement guide

Free download PDF
1.52 MB
How to change front anti roll bar links on SEAT Toledo II Saloon (1M2) – replacement guide

Free download PDF
624.64 KB
How to change rear strut mount on SEAT Toledo II Saloon (1M2) – replacement guide

Free download PDF
2.06 MB
How to change front wheel bearing on SEAT Toledo II Saloon (1M2) – replacement guide

Free download PDF
4.03 MB

How to change ball joint on a car – replacement tutorial

Universal

Free download PDF
2.05 MB
How to change front ball joint on Seat Ibiza 6L1 – replacement guide

Free download PDF
1.71 MB
How to change front ball joint on SEAT Leon Hatchback (1M1) – replacement guide

Free download PDF
1.4 MB
How to change front ball joint on SEAT AROSA (6H) – replacement guide

Free download PDF
1.58 MB
How to change front ball joint on SEAT Córdoba I Saloon (6K1, 6K2) – replacement guide

Free download PDF
1.73 MB
How to change front ball joint on SEAT Córdoba II Saloon (6L2) – replacement guide

Free download PDF
1.73 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

7 signs of faulty fuel injectors | AUTODOC tips

9K views

Published on: 09/01/2025
Top 7 signs of a bad starter

4K views

Published on: 20/03/2025
K2 ROTON wheel cleaner overview

3K views

Published on: 27/03/2025
How to easily repair a punctured tyre | AUTODOC tips

3K views

Published on: 25/02/2021