How to change front ball joint on RENAULT Symbol / Thalia II – replacement guide
downloads:
0
Views:
8
0
Users voted – 0
Important!
This replacement procedure can be used for:
RENAULT THALIA II (LU1/2_) 1.4,
RENAULT THALIA II (LU1/2_) 1.4,
RENAULT THALIA II (LU1/2_) 1.2 LPG,
RENAULT THALIA II (LU1/2_) 1.5 dCi,
RENAULT THALIA II (LU1/2_) 1.5 dCi,
RENAULT THALIA II (LU1/2_) 1.6 16V,
RENAULT THALIA II (LU1/2_) 1.2 16V (LU2V),
RENAULT THALIA II (LU1/2_) 1.5 dCi,
RENAULT THALIA II (LU1/2_) 1.5 dCi
…
View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Suspension Ball Joint for THALIA II (LU1/2_) and other RENAULT models
Replacement: ball joint – RENAULT THALIA II (LU1/2_). AUTODOC experts recommend:
The replacement procedure is identical for the left and right ball joints.
Please note: all work on the car – RENAULT THALIA II (LU1/2_) – should be done with the engine switched off.
Carry out replacement in the following order:
Step 1
Secure the wheels with chocks.
Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3
Raise the car.
Replacement: ball joint – RENAULT THALIA II (LU1/2_). Tip from AUTODOC experts:
If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
Step 4
Unscrew the wheel bolts.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. RENAULT THALIA II (LU1/2_)
Step 5
Remove the wheel.
Step 6
Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 7
Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 8
Unscrew the caliper bracket fastening. Use a drive socket #18. Use a ratchet wrench.
Step 9
Remove the fastening bolt.
Step 10
Clean the fasteners connecting the ball joint to the suspension control arm. Use a wire brush. Use WD-40 spray.
Step 11
Unscrew the fastener connecting the ball joint to the suspension control arm. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 12
Release the fastener connecting the ball joint to the steering knuckle. Use a crowbar.
Step 13
Disconnect the ball joint from the control arm.
Step 14
Disconnect the ball joint from the steering knuckle. Use a flat metal-working chisel. Use a hammer.
Step 15
Clean the ball joint mounting seat. Use a wire brush.
Step 16
Install a new ball joint.
Replacement: ball joint – RENAULT THALIA II (LU1/2_). AUTODOC experts recommend:
Do not damage the ball joint cover.
Step 17
Treat the fasteners of the ball joint. Use copper grease.
Step 18
Connect the ball joint to the steering knuckle.
Step 19
Attach the ball joint to the control arm.
Step 20
Screw in the fastener connecting the ball joint to the control arm. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 21
Install the fastening bolt.
Step 22
Screw the fastener connecting the ball joint to the steering knuckle. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 23
Tighten the brake caliper bracket. Use a drive socket #18. Use a torque wrench. Tighten it to 100 Nm torque.
Step 24
Tighten the fasteners connecting the ball joint to the control arm. Use a drive socket #18. Use a torque wrench. Tighten it to 75 Nm torque.
Step 25
Tighten the fastener connecting the ball joint to the steering knuckle. Use a combination spanner #16. Use a drive socket #16. Use a torque wrench. Tighten it to 55 Nm torque.
Step 26
Treat the fasteners of the ball joint. Use copper grease.
Step 27
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 28
Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends:
Replacement: ball joint – RENAULT THALIA II (LU1/2_). After applying the spray, wait a few minutes.
Step 29
Install the wheel.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. RENAULT THALIA II (LU1/2_)
Step 30
Screw in the wheel bolts. Use wheel impact socket #19.
Step 31
Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 90 Nm torque.
Step 32
Remove the jacks and chocks.
Replacement: ball joint – RENAULT THALIA II (LU1/2_). Tip from AUTODOC experts:
After replacing the component, it is advisable to realign the wheels using a wheel aligner.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Popular maintenance tutorials for RENAULT THALIA II (LU1/2_)
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your RENAULT THALIA II (LU1/2_)
View more
TOP 6 WD-40 lifehacks | AUTODOC tips
Causes of a worn car boot damper | AUTODOC
Car checks you need to carry out on your car after the winter | AUTODOC tips
5 car tips for a winter's day | AUTODOC tips
Most commonly replaced car parts on RENAULT SYMBOL / THALIA