Important!

This replacement procedure can be used for:
PEUGEOT 2008 Estate (CU_) 1.2 VTi, PEUGEOT 2008 Estate (CU_) 1.6 VTi, PEUGEOT 2008 Estate (CU_) 1.6 HDi, PEUGEOT 2008 Estate (CU_) 1.6 HDi, PEUGEOT 2008 Estate (CU_) 1.4 HDi, PEUGEOT 2008 Estate (CU_) 1.6 BlueHDi, PEUGEOT 2008 Estate (CU_) 1.2 THP / PureTech, PEUGEOT 2008 Estate (CU_) 1.2 THP / PureTech, PEUGEOT 2008 Estate (CU_) 1.6 BlueHDi, PEUGEOT 2008 Estate (CU_) 1.6 BlueHDi, PEUGEOT 2008 Estate (CU_) 1.6 BlueHDi, PEUGEOT 2008 Estate (CU_) 1.6 THP, PEUGEOT 2008 Estate (CU_) 1.2 PureTech, PEUGEOT 2008 Estate (CU_) 1.5 BlueHDI, PEUGEOT 2008 Estate (CU_) 1.5 BlueHDI, PEUGEOT 2008 Estate (CU_) 1.6 VTi … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – PEUGEOT 2008. Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #16
                    
                      Torx bit T30
                    
                      Drive socket # 17 
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Wheel chock

Buy tools

Replacement: anti roll bar links – PEUGEOT 2008. AUTODOC recommends:

Replace the stabiliser links on PEUGEOT 2008 in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
All work should be done with the engine stopped.

Replacement: anti roll bar links – PEUGEOT 2008. Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: anti roll bar links – PEUGEOT 2008. Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use Torx T30. Use a ratchet wrench.
Step 8

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #16. Use Torx T30. Use a ratchet wrench.
Step 9

Remove the stabilizer rod.

AUTODOC recommends:
Examine stabiliser bushes. Replace them if needed.
Step 10

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 11

Install a new rod, tighten the fasteners.
Step 12

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a torque wrench. Tighten it to 43 Nm torque.
Step 13

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #17. Use a torque wrench. Tighten it to 43 Nm torque.
Step 14

Treat all joints of the stabiliser link. Use copper grease.
Step 15

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 16

Clean the brake disk surface. Use a brake cleaner.

Replacement: anti roll bar links – PEUGEOT 2008. Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 17

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. PEUGEOT 2008
Step 18

Screw in the wheel bolts. Use wheel impact socket #17.
Step 19

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 100 nm torque.
Step 20

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT 2008 Estate (CU_) model

Peugeot 2008 Estate tyre size

How to change front lower arm on PEUGEOT 2008 Estate (CU_) – replacement guide

Free download PDF
2.68 MB
How to change front wheel bearing on PEUGEOT 2008 Estate (CU_) – replacement guide

Free download PDF
5.98 MB
How to change track rod end on PEUGEOT 2008 Estate (CU_) – replacement guide

Free download PDF
1.45 MB
How to change rear wheel bearing on PEUGEOT 2008 Estate (CU_) – replacement guide

Free download PDF
2.15 MB
How to change rear brake pads on PEUGEOT 2008 Estate (CU_) – replacement guide

Free download PDF
2.48 MB
How to change front brake pads on PEUGEOT 2008 Estate (CU_) – replacement guide

Free download PDF
1.43 MB

How to change front anti roll bar links on PEUGEOT 2008 II (U_) – replacement guide

Free download PDF
1.49 MB
How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on Peugeot 206 CC 2D – replacement guide

Free download PDF
1.32 MB
How to change front anti roll bar links on Peugeot 208 1 – replacement guide

Free download PDF
1.58 MB
How to change front anti roll bar links on Peugeot 307 SW – replacement guide

Free download PDF
1.33 MB
How to change front anti roll bar links on Peugeot 207 hatchback – replacement guide

Free download PDF
1.3 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Stop Rust Before It Starts: Top 5 Tips for Car Body Protection | AUTODOC Insights

7K views

Published on: 27/07/2023
DIY car soundproofing | AUTODOC tips

107K views

Published on: 15/04/2021
Top 5 reasons why your car squeals | AUTODOC Tips

10K views

Published on: 26/10/2023
DIY manual gearbox restoration | Drivetrain restoration – Part 3

18K views

Published on: 14/11/2024