Disclaimer
How to change front anti roll bar links on FORD PUMA (EC_) – replacement guide
downloads:
5
Views:
42
Important!
This replacement procedure can be used for:
FORD Puma Hatchback 1.7 16V, FORD Puma Hatchback 1.4 16V, FORD Puma Hatchback Racing ST 160, FORD Puma Hatchback 1.6 16V … View more
The steps may slightly vary depending on the car design.
FORD Puma Hatchback 1.7 16V, FORD Puma Hatchback 1.4 16V, FORD Puma Hatchback Racing ST 160, FORD Puma Hatchback 1.6 16V … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for Puma Hatchback and other FORD models
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #15
Combination spanner #17
Drive socket # 15
Drive socket # 17
Wheel impact socket #19
Ratchet wrench
Wheel chock
Replacement: anti roll bar links – FORD PUMA (EC_). AUTODOC recommends:
- Replace the stabiliser links on FORD PUMA (EC_) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – FORD PUMA (EC_) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. FORD PUMA (EC_) - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench. - Step 9
Remove the stabilizer rod. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Install a new rod, tighten the fasteners. Use a combination spanner #15. Use a drive socket #15. Use a ratchet wrench.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the FORD Puma Hatchback model.
Popular maintenance tutorials for Ford Puma Coupe
Free download PDF
1.66 MB
Free download PDF2.88 MB
Free download PDF1.48 MB
Free download PDF1.51 MB
Free download PDF2.39 MB
Free download PDF7.83 MB
Complete guides for changing the Drop links on different FORD PUMA models
Free download PDF1.25 MB
Free download PDF972.8 KB
Free download PDF1.99 MB
Free download PDF1.29 MB
Free download PDF1.27 MB
Free download PDF1.23 MB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your FORD Puma Hatchback
View more
What to do if your check engine light is on | AUTODOC tips
How to reduce fuel consumption | AUTODOC
5 car tips for a winter's day | AUTODOC tips
Coolant comparison test | AUTODOC
