Recommended replacement interval for the part category Oil filter : 1 year / 15000 km

Important!

This replacement procedure can be used for:
TOYOTA Urban Cruiser (_P1_) 1.8 (ZSP110_) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Oil filter

Replacement: engine oil and filter – TOYOTA URBAN CRUISER (NSP1_, NLP1_, ZSP1_, NCP11_). List of the tools you'll need:

                      All-purpose cleaning spray
                    
                      Combination spanner #14
                    
                      Oil filter cup socket 65-14F
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Oil drain pan
                    
                      Funnel
                    
                      Fender cover

Buy tools

Replacement: engine oil and filter – TOYOTA URBAN CRUISER (NSP1_, NLP1_, ZSP1_, NCP11_). Tip from AUTODOC experts:

Replace the oil filter every time when changing motor oil.
Wear gloves to prevent contact with hot liquid.
All work should be done with the engine stopped.

Replacement: engine oil and filter – TOYOTA URBAN CRUISER (NSP1_, NLP1_, ZSP1_, NCP11_). Take the following steps:

Step 1

Lift the car using a jack or place it over an inspection pit.

Replacement: engine oil and filter – TOYOTA URBAN CRUISER (NSP1_, NLP1_, ZSP1_, NCP11_). AUTODOC recommends:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.
Step 2

Put a waste oil container with at least 5 l capacity under the drainage hole.
Step 3

Unscrew the oil filter. Use the 65-14F socket. Use a ratchet wrench.
Step 4

Put the old oil filter in the container.

Replacement: engine oil and filter – TOYOTA URBAN CRUISER (NSP1_, NLP1_, ZSP1_, NCP11_). Tip:
Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
Step 5

Clean the oil filter seat.

Step 6

Screw the new filter into its place. Use the 65-14F socket. Use a torque wrench. Tighten it to 18 Nm torque.
Step 7

Unscrew the drain plug. Use a combination spanner #14.
Step 8

Drain the used oil.

Replacement: engine oil and filter – TOYOTA URBAN CRUISER (NSP1_, NLP1_, ZSP1_, NCP11_). Tip from AUTODOC:
Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
Step 9

Clean the area of the oil pan drainage hole.
Step 10

Screw in the new drainage plug and tighten it. Use a combination spanner #14. Use a torque wrench. Tighten it to 25 Nm torque.
Step 11

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.

Step 12

Lower the car. Open the hood.

Step 13

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 14

Unscrew the oil filler plug.
Step 15

Remove the oil filler cap.

Step 16

Insert the funnel.
Step 17

Pour new oil into the engine in the amount recommended by the car manufacturer.

Replacement: engine oil and filter – TOYOTA URBAN CRUISER (NSP1_, NLP1_, ZSP1_, NCP11_). Tip from AUTODOC experts:
Use the oil recommended by the manufacturer.
Step 18

Check the oil level using the dipstick. Top up oil if necessary.

Please note!
The oil level should be between the Min and Max marks.
Step 19

Install the oil filler cap.
Step 20

Tighten the oil filler cap.

Step 21

Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.
Step 22

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

Please note!
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 23

Remove the fender protection cover. Close the hood.

Replacement: engine oil and filter – TOYOTA URBAN CRUISER (NSP1_, NLP1_, ZSP1_, NCP11_). Professionals recommend:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out. To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Urban Cruiser (XP110) model

Toyota Urban Cruiser XP11 tyre size

How to change air filter on TOYOTA Urban Cruiser (_P1_) – replacement guide

Free download PDF
952.32 KB
How to change pollen filter on TOYOTA Urban Cruiser (_P1_) – replacement guide

Free download PDF
675.84 KB
How to change front brake pads on TOYOTA Urban Cruiser (_P1_) – replacement guide

Free download PDF
1.56 MB
How to change rear brake pads on TOYOTA Urban Cruiser (_P1_) – replacement guide

Free download PDF
1.41 MB
How to change front wheel bearing on TOYOTA Urban Cruiser (XP110) – replacement guide

Free download PDF
3.91 MB
How to change front wheel bearing on TOYOTA Urban Cruiser (_P1_) – replacement guide

Free download PDF
3.7 MB

How to change engine oil and filter on a car – replacement tutorial

Universal

Free download PDF
2.82 MB
How to change engine oil and filter on Toyota Aygo AB1 – replacement guide

Free download PDF
2.32 MB
How to change engine oil and filter on Toyota Auris E15 – replacement guide

Free download PDF
2.23 MB
How to change engine oil and filter on Toyota Prado J120 – replacement guide

Free download PDF
2.23 MB
How to change engine oil and filter on Toyota Yaris Mk2 – replacement guide

Free download PDF
1.87 MB
How to change engine oil and filter on Toyota RAV4 III – replacement guide

Free download PDF
2.16 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to Fix P0401 ✅ error code Insufficient EGR flow

7K views

Published on: 08/05/2025
DIY vehicle AC compressor restoration

747K views

Published on: 28/11/2024
Top 5 reasons why the suspension knocks | AUTODOC tips

2M views

Published on: 09/09/2022
How I started restoring a driveshaft | Drivetrain restoration – Part 1

8K views

Published on: 17/10/2024