Recommended replacement interval for the part category Oil filter : 12 month / 15000 km

Important!

This replacement procedure can be used for:
TOYOTA Sienna IV (XL40) 2.5 Hybrid Allrad (AXLH45) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Oil Filter for Sienna IV (XL40) and other TOYOTA models

Oil filter

Oil filter for Sienna IV (XL40) Petrol/Electric (246 hp)

Replacement: engine oil and filter – TOYOTA Sienna IV (XL40). List of the tools you'll need:

                        All-purpose cleaning spray
                      
                        Oil filter cup socket 76/14-F
                      
                        Impact socket №15
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Oil drain pan
                      
                        Funnel
                      
                        Fender cover

Buy tools

AUTODOC recommends:

Replace the oil filter every time when changing motor oil.
Please note: all work on the car – TOYOTA Sienna IV (XL40) – should be done with the engine switched off.
Wear gloves to prevent contact with hot liquid.

Carry out replacement in the following order:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Unscrew the oil filler plug.

Step 4

Lift the car using a jack or place it over an inspection pit.

Replacement: engine oil and filter – TOYOTA Sienna IV (XL40). Tip from AUTODOC experts:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped.
Step 5

Put a waste oil container with at least 4 l capacity under the drainage hole.
Step 6

Unscrew the drain plug. Use a drive socket #15. Use a ratchet wrench.
Step 7

Drain the used oil.

Replacement: engine oil and filter – TOYOTA Sienna IV (XL40). Tip from AUTODOC:
Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
Step 8

Move the container under the oil filter.
Step 9

Unscrew the oil filter. Use the 76/14-F socket.
Step 10

Prepare a container for the old oil filter. Put the old oil filter in the container.

Replacement: engine oil and filter – TOYOTA Sienna IV (XL40). Tip:
Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
Step 11

Clean the oil filter seat.
Step 12

Lubricate the rubber seal of the new filter with a little amount of fresh oil.
Step 13

Screw the new filter into its place. Use the 76/14-F socket. Use a torque wrench. Tighten it to 23 nm torque.
Step 14

Clean the area of the oil pan drainage hole.
Step 15

Screw in the new drainage plug and tighten it. Use a drive socket #15. Use a torque wrench. Tighten it to 27 nm torque.
Step 16

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 17

Lower the car.

Step 18

Remove the oil filler cap. Insert the funnel.
Step 19

Pour new oil into the engine in the amount recommended by the car manufacturer.

Replacement: engine oil and filter – TOYOTA Sienna IV (XL40). Professionals recommend:
Use the oil recommended by the manufacturer.
Step 20

Check the oil level using the dipstick. Top up oil if necessary.

Please note!
The oil level should be between the Min and Max marks.
Step 21

Tighten the oil filler cap.
Step 22

Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.

Step 23

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

Replacement: engine oil and filter – TOYOTA Sienna IV (XL40). AUTODOC recommends:
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 24

Remove the fender protection cover.

Step 25

Close the hood.

Replacement: engine oil and filter – TOYOTA Sienna IV (XL40). AUTODOC experts recommend:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out. To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Sienna IV (XL40) model.

TOYOTA Sienna IV (XL40) tyre size

How to change engine oil and filter on Toyota Aygo AB1 – replacement guide

Free download PDF
2.32 MB
How to change rear brake shoes on Toyota Yaris P1 – replacement guide

Free download PDF
2.32 MB
How to change front anti roll bar links on Toyota Yaris P1 – replacement guide

Free download PDF
1.61 MB
How to change front brake pads on Toyota Prado J120 – replacement guide

Free download PDF
2.08 MB
How to change serpentine belt on Toyota Aygo AB1 – replacement guide

Free download PDF
2.36 MB
How to change engine oil and filter on Toyota Auris E15 – replacement guide

Free download PDF
2.23 MB

How to change engine oil and filter on TOYOTA SIENNA (ASL3_, GSL3_) – replacement guide

Free download PDF
1.76 MB
How to change engine oil and filter on TOYOTA SIENNA (MCL2_, GSL2_) – replacement guide

Free download PDF
1.63 MB
How to change engine oil and filter on a car – replacement tutorial

Universal

Free download PDF
2.82 MB
How to change engine oil and filter on Toyota Aygo AB1 – replacement guide

Free download PDF
2.32 MB
How to change engine oil and filter on Toyota Auris E15 – replacement guide

Free download PDF
2.23 MB
How to change engine oil and filter on Toyota Yaris Mk2 – replacement guide

Free download PDF
1.87 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

DIY alternator repair | AUTODOC tips

1M views

Published on: 30/11/2022
Top 5 tips to prevent car rust | AUTODOC tips

5K views

Published on: 27/07/2023
How to paint a brake caliper | AUTODOC tips

10K views

Published on: 08/04/2021
How to unlock your car without a key | AUTODOC tips

860K views

Published on: 15/09/2022