Recommended replacement interval for the part category Oil filter : 12 month / 15000 km

Important!

This replacement procedure can be used for:
TOYOTA SIENNA (ASL3_, GSL3_) 3.5 (GSL30_) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Oil Filter for SIENNA (ASL3_, GSL3_) and other TOYOTA models

Oil filter

Oil filter for Sienna III (XL30) Petrol (269 hp)

Replacement: engine oil and filter – TOYOTA SIENNA (ASL3_, GSL3_). Tools you'll need:

                        Wire brush
                      
                        All-purpose cleaning spray
                      
                        Combination spanner #14
                      
                        Drive socket # 14 
                      
                        Oil filter cup socket 67-14F
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Flat Screwdriver
                      
                        Clip removal tool
                      
                        Oil drain pan
                      
                        Funnel
                      
                        Fender cover

Buy tools

Replacement: engine oil and filter – TOYOTA SIENNA (ASL3_, GSL3_). AUTODOC experts recommend:

Replace the oil filter every time when changing motor oil.
All work should be done with the engine stopped.
Wear gloves to prevent contact with hot liquid.

Replacement: engine oil and filter – TOYOTA SIENNA (ASL3_, GSL3_). Use the following procedure:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Unscrew the oil filler plug.
Step 4

Lift the car using a jack or place it over an inspection pit.

Replacement: engine oil and filter – TOYOTA SIENNA (ASL3_, GSL3_). AUTODOC experts recommend:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.
Step 5

Undo the fasteners of the oil pan lower cover. Use a clip removal tool.
Step 6

Remove the oil pan cover.
Step 7

Put a waste oil container with at least 5 l capacity under the drainage hole.
Step 8

Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.
Step 9

Unscrew the drain plug. Use a combination spanner #14. Use a drive socket #14. Use a ratchet wrench.
Step 10

Drain the used oil.

Replacement: engine oil and filter – TOYOTA SIENNA (ASL3_, GSL3_). Tip from AUTODOC:
Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
Step 11

Prepare a container for the old oil filter.

Step 12

Unscrew the filter housing cap together with the old filter element. Use the 67-14F socket. Use a ratchet wrench.
Step 13

Put the old oil filter in the container.

Replacement: engine oil and filter – TOYOTA SIENNA (ASL3_, GSL3_). Tip from AUTODOC experts:
Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
Step 14

Detach the oil filter from the filter cover.
Step 15

Remove the oil filter cover O-ring. Use a flat screwdriver.
Step 16

Clean the oil filter housing cap. Use all-purpose cleaning spray.
Step 17

Install a new O-ring to its mounting seat on the filter cover.
Step 18

Install the new oil filter to the mounting seat on the filter cover.

Please note!
Make sure to install the filter correctly. Don't mix up the sides of the part.
Step 19

Clean the oil filter seat. Use all-purpose cleaning spray.
Step 20

Lubricate the rubber seal of the new filter with a little amount of fresh oil.
Step 21

Screw the new filter into its place.
Step 22

Screw the cap. Use the 67-14F socket. Use a torque wrench. Tighten it to 25 Nm torque.
Step 23

Clean the area of the oil pan drainage hole.
Step 24

Screw in the new drainage plug and tighten it. Use a drive socket #14. Use a torque wrench. Tighten it to 27 Nm torque.
Step 25

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 26

Reinstall the oil pan lower cover.
Step 27

Tighten the fasteners of the oil pan lower cover.
Step 28

Lower the car.

Step 29

Remove the oil filler cap.
Step 30

Insert the funnel.
Step 31

Pour new oil into the engine in the amount recommended by the car manufacturer.

Replacement: engine oil and filter – TOYOTA SIENNA (ASL3_, GSL3_). Tip:
Use the oil recommended by the manufacturer.
Step 32

Check the oil level using the dipstick. Top up oil if necessary.

Please note!
The oil level should be between the Min and Max marks.
Step 33

Install the oil filler cap. Tighten the oil filler cap.
Step 34

Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.

Step 35

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

Please note!
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 36

Remove the fender protection cover.

Step 37

Close the hood.

Replacement: engine oil and filter – TOYOTA SIENNA (ASL3_, GSL3_). AUTODOC experts recommend:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out. To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Sienna III (XL30) model.

Toyota Sienna ASL3 tyre size

How to change pollen filter on TOYOTA SIENNA (ASL3_, GSL3_) – replacement guide

Free download PDF
655.36 KB
How to change engine oil and filter on Toyota Aygo AB1 – replacement guide

Free download PDF
2.32 MB
How to change rear brake shoes on Toyota Yaris P1 – replacement guide

Free download PDF
2.32 MB
How to change front anti roll bar links on Toyota Yaris P1 – replacement guide

Free download PDF
1.61 MB
How to change front brake pads on Toyota Prado J120 – replacement guide

Free download PDF
2.08 MB
How to change serpentine belt on Toyota Aygo AB1 – replacement guide

Free download PDF
2.36 MB

How to change engine oil and filter on TOYOTA SIENNA (MCL2_, GSL2_) – replacement guide

Free download PDF
1.63 MB
How to change engine oil and filter on TOYOTA Sienna IV (XL40) – replacement guide

Free download PDF
1.15 MB
How to change engine oil and filter on a car – replacement tutorial

Universal

Free download PDF
2.82 MB
How to change engine oil and filter on Toyota Aygo AB1 – replacement guide

Free download PDF
2.32 MB
How to change engine oil and filter on Toyota Auris E15 – replacement guide

Free download PDF
2.23 MB
How to change engine oil and filter on Toyota Yaris Mk2 – replacement guide

Free download PDF
1.87 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to remove rust | AUTODOC tips

25K views

Published on: 16/09/2021
How to remove scratches from a car | AUTODOC tips

7K views

Published on: 12/05/2022
3 things to know before buying summer tyres | AUTODOC tips

3K views

Published on: 18/05/2023
How to polish an old engine valve cover to a shiny finish | AUTODOC Tips

8K views

Published on: 30/11/2023