Disclaimer
How to change engine oil and filter on Peugeot 206 CC 2D – replacement guide
downloads:
46
Views:
1276
Recommended replacement interval for the part category Oil filter : 2 year / 30000 km
Important!
This replacement procedure can be used for:
PEUGEOT 206 CC (2D) 1.6 16V (2DNFUF, 2DNFUR) … View more
The steps may slightly vary depending on the car design.
PEUGEOT 206 CC (2D) 1.6 16V (2DNFUF, 2DNFUR) … View more
The steps may slightly vary depending on the car design.
How to change oil filter and engine oil on PEUGEOT 206 1 (2D) [TUTORIAL AUTODOC]

All the parts you need to replace – Oil Filter for 206 CC (2D) and other PEUGEOT models
Alternative products

All-purpose cleaning spray
Drive socket # 24
Drive socket # 27
Torque wrench
Flat Screwdriver
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – Peugeot 206 CC 2D. AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- All work should be done with the engine stopped.
- Wear gloves to prevent contact with hot liquid.
Replacement: engine oil and filter – Peugeot 206 CC 2D. Use the following procedure:
- Step 1
Open the hood. - Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car. - Step 3
Unscrew the oil filler plug. - Step 4
Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – Peugeot 206 CC 2D. AUTODOC experts recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped. - Step 5
Put a waste oil container with at least 5 l capacity under the drainage hole. - Step 6
Unscrew the drain plug. Use a drive socket #24. - Step 7
Drain the used oil.Replacement: engine oil and filter – Peugeot 206 CC 2D. Tip from AUTODOC:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter. - Step 8
Unscrew the filter housing cap together with the old filter element. Use a drive socket #27. - Step 9
Prepare a container for the old oil filter. - Step 10
Put the old filter cartridge in the container. - Step 11
Remove the filter element from the filter housing. - Step 12
Remove the oil filter cover O-ring. Use a flat screwdriver. - Step 13
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 14
Install a new O-ring to its mounting seat on the filter cover. - Step 15
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 16
Screw the new filter into its place. - Step 17
Screw the cap. Use a drive socket #27. Use a torque wrench. Tighten it to 25 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the PEUGEOT 206 CC (2D) model
Popular maintenance tutorials for Peugeot 206 cc 2d
Complete guides for changing the Oil filters on different PEUGEOT 206 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your PEUGEOT 206 CC (2D)
View more
How to Polish Your Car Yourself and Save Money on Garage Services | AUTODOC tips
7 signs of faulty fuel injectors | AUTODOC tips
Top 7 Manual Transmission Mistakes to Avoid | AUTODOC Tips
5 most common causes of oil leaks | AUTODOC tips
Most commonly replaced car parts on PEUGEOT 206
Time to replace parts? Get even better deals in our Shop app.

SCAN ME






























