Disclaimer
How to change wheel cylinder on VW SCIROCCO (53) – replacement guide
downloads:
0
Views:
2
Recommended replacement interval for the part category Wheel Brake Cylinder : 60000 km
Important!
This replacement procedure can be used for:
VW SCIROCCO (53) 1.6, VW SCIROCCO (53) 1.6, VW SCIROCCO (53) 1.6 … View more
The steps may slightly vary depending on the car design.
VW SCIROCCO (53) 1.6, VW SCIROCCO (53) 1.6, VW SCIROCCO (53) 1.6 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Cylinder for SCIROCCO (53) and other VW models
Alternative products

Wire brush
WD-40 spray
Copper grease
Combination spanner #7
Combination spanner #11
Torx bit T30
Wheel impact socket #17
Ratchet wrench
Torque wrench
Flat Screwdriver
Phillips screwdriver
Wheel chock
Replacement: wheel cylinder – VW SCIROCCO (53). Tip from AUTODOC:
- Replace the wheel brake cylinders of the rear drum brakes in pairs.
- The replacement procedure is identical for the right and left wheel brake cylinders of the rear drum brakes.
- All work should be done with the engine stopped.
Replacement: wheel cylinder – VW SCIROCCO (53). Recommended sequence of steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW SCIROCCO (53) - Step 5
Remove the wheel. - Step 6Clean the brake drum fasteners. Use a wire brush. Use WD-40 spray.Step 7
Unscrew the brake drum fastening. Use a Phillips screwdriver. - Step 8
Remove the brake drum.Replacement: wheel cylinder – VW SCIROCCO (53). Tip from AUTODOC experts:Examine the brake drum. Replace it if necessary. - Step 9
Disconnect the hydraulic line from the wheel cylinder back. Use a combination spanner #11.Replacement: wheel cylinder – VW SCIROCCO (53). Tip from AUTODOC:Immediately plug the brake line open end to prevent fluid leakage and ingress of dirt into the hydraulic system. - Step 10
Unscrew the brake cylinder fastening bolt. Use Torx T30. Use a ratchet wrench. - Step 11
Remove the brake cylinder from the backplate. Use a flat screwdriver. - Step 12Clean the brake drum. Use a wire brush. Use WD-40 spray.Step 13Clean the brake pipe attachment spot and the brake drum fastening bolts on :maker :model.Step 14
Install a new brake cylinder. - Step 15
Screw the brake cylinder fastening bolts. Use Torx T30. Use a torque wrench. Tighten it to 8 nm torque. - Step 16
Connect the hydraulic line to the wheel cylinder back. Use a combination spanner #11. Use a torque wrench. Tighten it to 14 nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Scirocco I (53) model
Popular maintenance tutorials for VW Scirocco 1
Complete guides for changing the Brake wheel cylinder on different VW SCIROCCO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW SCIROCCO (53)
View more
Top 5 Car Interior Cleaning Mistakes You Should Avoid | AUTODOC Tips
Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide
5 Essential Tips for beginner drivers: Avoid Common Mistakes
5 Essential Tips to Prepare Your Car for Winter | AUTODOC tips
Most commonly replaced car parts on VW SCIROCCO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME






























