Disclaimer
How to change track rod end on OPEL Tigra TwinTop (X04) – replacement guide
downloads:
1
Views:
15
Important!
This replacement procedure can be used for:
OPEL Tigra TwinTop (X04) 1.3 CDTI (R97), OPEL Tigra TwinTop (X04) 1.8 (R97), OPEL Tigra TwinTop (X04) 1.4 (R97) … View more
The steps may slightly vary depending on the car design.
OPEL Tigra TwinTop (X04) 1.3 CDTI (R97), OPEL Tigra TwinTop (X04) 1.8 (R97), OPEL Tigra TwinTop (X04) 1.4 (R97) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Tigra TwinTop (X04) and other OPEL models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #19
Drive socket # 17
Wheel impact socket #17
Ratchet wrench
Torque wrench
Vernier caliper
Ball joint puller
Wheel chock
Replacement: track rod end – OPEL TIGRA TwinTop. AUTODOC recommends:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – OPEL TIGRA TwinTop. Use the following procedure:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. OPEL TIGRA TwinTop - Step 5
Remove the wheel. - Step 6Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.Step 7
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper. - Step 8
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench. - Step 9
Disconnect the tie rod end from the steering knuckle. Use a ball joint puller. - Step 10
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #19. - Step 11
Screw the end out of the tie rod. - Step 12
Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray. - Step 13
Screw on a new tie rod end.Replacement: track rod end – OPEL TIGRA TwinTop. Professionals recommend:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the OPEL Tigra Twintop (X04) model
Popular maintenance tutorials for Opel Tigra Twintop
Complete guides for changing the Tie rod end on different OPEL TIGRA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your OPEL Tigra TwinTop (X04)
View more
DIY rear axle restoration | Drivetrain restoration – Part 2
Understanding Airbag Light Warnings | Essential Tips for Car Safety
5 mistakes made when washing the engine | AUTODOC tips
Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips
Most commonly replaced car parts on OPEL TIGRA
ОЕ number
Time to replace parts? Get even better deals in our Shop app.

SCAN ME























