Disclaimer
How to change track rod end on NISSAN NAVARA (D22) – replacement guide
downloads:
7
Views:
263
Important!
This replacement procedure can be used for:
NISSAN NAVARA (D22) 2.5 TDiC 4x4, NISSAN NAVARA (D22) 2.5 D 4x4, NISSAN NAVARA (D22) 2.5 D 4x4, NISSAN NAVARA (D22) 2.5 TD 4x4 … View more
The steps may slightly vary depending on the car design.
NISSAN NAVARA (D22) 2.5 TDiC 4x4, NISSAN NAVARA (D22) 2.5 D 4x4, NISSAN NAVARA (D22) 2.5 D 4x4, NISSAN NAVARA (D22) 2.5 TD 4x4 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for NAVARA (D22) and other NISSAN models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #22
Drive socket # 22
Wheel impact socket #21
Ratchet wrench
Torque wrench
Nippers
Ball joint puller
Vernier caliper
Wheel chock
Replacement: track rod end – NISSAN NAVARA (D22). AUTODOC recommends:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – NISSAN NAVARA (D22). Take the following steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #21. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: track rod end – NISSAN NAVARA (D22). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper. - Step 7
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #22. - Step 8
Remove the cotter pin fixing the tie rod end fastening. Use nippers. - Step 9Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.Step 10
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #22. Use a ratchet wrench. - Step 11
Disconnect the tie rod end from the steering knuckle. Use a ball joint puller. - Step 12
Screw the end out of the tie rod. - Step 13Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.Step 14
Screw on a new tie rod end.Replacement: track rod end – NISSAN NAVARA (D22). AUTODOC experts recommend:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements. - Step 15
Connect the tie rod end to the steering knuckle.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the NISSAN Navara Pickup (D22) model
Popular maintenance tutorials for Nissan Navara D22
Complete guides for changing the Tie rod end on different NISSAN NAVARA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your NISSAN NAVARA (D22)
View more
5 signs of a faulty strut mount and how to fix it
Top Automatic Transmission Blunders You Must Dodge | AUTODOC Insights
How to Prevent Premature Wear on Your Car Boot Damper | AUTODOC
TOP 5 mistakes during DIY oil change | AUTODOC tips
Most commonly replaced car parts on NISSAN NAVARA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























