Important!

This replacement procedure can be used for:
FIAT GRANDE PUNTO (199) 1.3 D Multijet, LINCOLN Mark LT I 5.4 4x4, FIAT PUNTO EVO (199) 1.3 D Multijet, FIAT PUNTO Van (199) 1.3 D Multijet, FIAT PUNTO (199) 1.3 D Multijet

The steps may slightly vary depending on the car design.

How to change tie rod end / track rod end on FIAT PUNTO 199 [TUTORIAL AUTODOC]

Replacement: track rod end – Fiat Punto 199. Tools you need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner
                      
                        Copper grease
                      
                        Combination spanner #15
                      
                        Combination spanner #22
                      
                        Drive socket # 17
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Tap wrench
                      
                        Vernier caliper
                      
                        Wheel chock

All the parts you need to replace – Track Rod End for GRANDE PUNTO (199) and other FIAT models

FIAT PUNTO EVO (199) 1.3 D Multijet

FIAT GRANDE PUNTO (199) 1.3 D Multijet

FIAT PUNTO EVO (199) 1.3 D Multijet

FIAT GRANDE PUNTO (199) 1.3 D Multijet

    FIAT PUNTO EVO (199) 1.3 D Multijet
  
    FIAT GRANDE PUNTO (199) 1.3 D Multijet
  
    LINCOLN Mark LT I 5.4 4x4
  
    FIAT PUNTO (199) 1.3 D Multijet
  
    FIAT PUNTO Van (199) 1.3 D Multijet

Replacement: track rod end – Fiat Punto 199. AUTODOC recommends:

Replace tie rod ends in pairs.
The replacement procedure is identical for the right and left tie rod ends.
All work should be done with the engine stopped.

Replacement: track rod end – Fiat Punto 199. Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts.Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

AUTODOC recommends:

Important! Hold the wheel while unscrewing the fastening bolts. Fiat Punto 199
Step 5

Remove the wheel.
Step 6

Clean the fastener connecting the tie rod end to the steering knuckle.Use a wire brush.Use WD-40 spray.
Step 7

Unscrew the end fastening nut to the steering knuckle.Use a drive socket #17.Use a tap wrench.
Step 8

When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward.Use a vernier caliper.
Step 9

Loosen the lock nut securing the tie rod end to the tie rod.Use a combination spanner #22.
Step 10

Disconnect the tie rod end from the steering knuckle.
Step 11

Screw the end out of the tie rod.
Step 12

Clean the mounting seats of the tie rod end.Use a wire brush.Use WD-40 spray.
Step 13

Screw on a new tie rod end.

Replacement: track rod end – Fiat Punto 199. Tip from AUTODOC experts:

While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
Step 14

Connect the tie rod end to the steering knuckle.
Step 15

Screw on the fastening nut that connects the tie rod end to the steering knuckle.Use a drive socket #17.Use a ratchet wrench.
Step 16

When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward.Use a vernier caliper.
Step 17

Tighten the tie rod end locknut.Use a combination spanner #15.Use a combination spanner #22.Use a torque wrench.Tighten it to 50 nm torque.
Step 18

Tighten the fastening nut connecting the tie rod end to the steering knuckle.Use a drive socket #17.Use a torque wrench.Tighten it to 70 nm torque.
Step 19

Treat the fastener connecting the tie rod end to the steering knuckle.Use copper grease.
Step 20

Treat the surface where the brake disc contacts the wheel rim.Use copper grease.
Step 21

Clean the brake disk surface.Use a brake cleaner.

Replacement: track rod end – Fiat Punto 199. Tip:

After applying the spray, wait a few minutes.
Step 22

Install the wheel.

AUTODOC recommends:

Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Fiat Punto 199
Step 23

Screw in the wheel bolts.Use wheel impact socket #17.
Step 24

Lower the car and working in a cross order, tighten the wheel bolts.Use wheel impact socket #17.Use a torque wrench.Tighten it to 120 nm torque.

Replacement: track rod end – Fiat Punto 199. Tip from AUTODOC experts:

Check and adjust wheel alignment if necessary.
Step 25

Remove the jacks and chocks.

Comment

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

How to change: Fiat Punto 199 front anti roll bar links – replacement guide

Free download PDF

5.38 MB
How to change front lower arm on Fiat Punto 199 – replacement guide

Free download PDF

8.01 MB
How to change: Fiat Doblo Cargo engine oil and filter – replacement guide

Free download PDF

8.65 MB
How to change: Fiat Doblo Cargo air filter – replacement guide

Free download PDF

4.19 MB
How to change: Fiat Punto 199 air filter – replacement guide

Free download PDF

3.98 MB
How to change: Fiat Punto 199 fuel filter – replacement guide

Free download PDF

5.19 MB
How to change: Fiat Punto 199 pollen filter – replacement guide

Free download PDF

4.54 MB
How to change: Fiat Punto 199 front windshield wipers – replacement guide

Free download PDF

2.59 MB
How to change: Fiat Punto 199 engine oil and filter – replacement guide

Free download PDF

9.07 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Tips & tricks for your FIAT GRANDE PUNTO (199)

How to clean an engine bay | AUTODOC

4K views

Published on: 11/09/2020
How to prevent car windows from fogging up | AUTODOC tips

4K views

Published on: 04/02/2021
Checking the starter without removing it | AUTODOC tips

2K views

Published on: 01/12/2020
How to check your head gasket | AUTODOC

4K views

Published on: 13/10/2020