Important!

This replacement procedure can be used for:
TOYOTA Yaris Hatchback (_P13_) 1.0 (KSP130), TOYOTA Yaris Hatchback (_P13_) 1.8 GRMN (NSP131_), TOYOTA Yaris Hatchback (_P13_) 1.5 (NSP131_), TOYOTA Yaris Hatchback (_P13_) 1.3 (NSP130_), TOYOTA Yaris Hatchback (_P13_) 1.4 D (NLP130_), TOYOTA Yaris Hatchback (_P13_) 1.0 (KSP130_), TOYOTA Yaris Hatchback (_P13_) 1.3 (NSP130_) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Replacement: wheel bearing – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_). Tools you'll need:

                        Wire brush
                      
                        Nylon cleaning brush
                      
                        WD-40 spray
                      
                        All-purpose cleaning spray
                      
                        Brake cleaner 
                      
                        Electronic spray
                      
                        Anti-squeal paste
                      
                        Ceramic grease
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Drive socket # 14
                      
                        HEX bit No.H7
                      
                        Wheel impact socket #21
                      
                        Ratchet wrench
                      
                        Flat screwdriver
                      
                        Hammer
                      
                        Crow bar
                      
                        Hydraulic transmission jack
                      
                        Wheel chock

Buy tools

AUTODOC recommends:

Do not re-use the bearing assembly of your TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_) car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
Please note: all work on the car – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet. Unscrew the brake fluid reservoir cap.

Step 2

Secure the wheels with chocks.

Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 4

Raise the car.

Replacement: wheel bearing – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_). Tip from AUTODOC experts:
If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
Step 5

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_)
Step 6

Remove the wheel.
Step 7

Detach the brake caliper retaining spring. Use a crowbar.
Step 8

Remove the dust boot caps of the brake caliper guide pins. Use a crowbar.
Step 9

Unscrew the brake caliper fasteners. Use HEX No.H7. Use a ratchet wrench.
Step 10

Remove the brake caliper. Use a crowbar.

Replacement: wheel bearing – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_). Tip:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 11

Remove the brake pads.
Step 12

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 13

Unscrew the brake caliper bracket fasteners. Use a drive socket #14. Use a ratchet wrench.
Step 14

Remove the fastening bolts.
Step 15

Remove the caliper bracket.
Step 16

Remove the brake disc.
Step 17

Clean the ABS sensor fastener. Use a nylon cleaning brush. Use all-purpose cleaning spray.
Step 18

Detach the ABS sensor connector. Use a flat screwdriver.
Step 19

Clean the wheel hub fastener. Use a wire brush. Use WD-40 spray.
Step 20

Support the rear suspension beam. Use a hydraulic transmission jack.
Step 21

Unscrew the wheel hub bearing fasteners. Use a drive socket #14. Use a ratchet wrench.
Step 22

Remove the fastening bolts.
Step 23

Remove the hub and the bearing together, since they are made as an assembly. Use a crowbar. Use a hammer.
Step 24

Clean the hub bearing mounting seat. Use a wire brush. Use all-purpose cleaning spray.
Step 25

Treat the wheel hub mounting seat. Use copper grease.
Step 26

Install the new wheel hub together with the bearing.
Step 27

Install the fastening bolts.
Step 28

Tighten the wheel hub bearing fasteners. Use a drive socket #14. Use a torque wrench. Tighten it to 90 nm torque.
Step 29

Treat the fasteners of the wheel hub bearing. Use copper grease.
Step 30

Remove the support from under the rear axle beam.

AUTODOC recommends:
Replacement: wheel bearing – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 31

Treat the hub where it contacts the brake disk. Use ceramic grease.
Step 32

Install the brake disc.
Step 33

Treat the ABS sensor connector. Use dielectric grease.
Step 34

Attach the ABS sensor connector.
Step 35

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_). After applying the spray, wait a few minutes.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 36

Install the brake caliper bracket.
Step 37

Install the fastening bolts.
Step 38

Tighten the brake caliper bracket fasteners. Use a drive socket #14. Use a torque wrench. Tighten it to 57 Nm torque.
Step 39

Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.

Replacement: wheel bearing – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_). Tip from AUTODOC experts:
Make sure the disc surface is clean before installing the pads.
Step 40

Install the brake pads.
Step 41

Install the brake caliper and fix it.
Step 42

Tighten the brake caliper fasteners. Use HEX No.H7. Use a torque wrench. Tighten it to 34 nm torque.
Step 43

Install the dust boot caps of the brake caliper guide pins.
Step 44

Install the brake caliper retaining spring.
Step 45

Clean the wheel rim mounting seat. Use a wire brush.
Step 46

Treat the surface where the brake disc contacts the wheel rim. Use ceramic grease.
Step 47

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_). After applying the spray, wait a few minutes.
Step 48

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_)
Step 49

Screw in the wheel bolts. Use wheel impact socket #21.
Step 50

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 103 Nm torque.
Step 51

Remove the jacks and chocks.

Replacement: wheel bearing – TOYOTA YARIS (NHP13_, NSP13_, NCP13_, KSP13_, NLP13_). Tip from AUTODOC experts:
Without starting the engine, press the brake pedal several times until you feel significant resistance.Check the brake fluid level in the expansion tank and refill if necessary.
Step 52

Tighten the brake fluid reservoir cap. Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Yaris III Hatchback (XP13) model.

Browse tyres

How to change front wheel bearing on TOYOTA Yaris III Hatchback (XP13) – replacement guide

Free download PDF
3.91 MB
How to change front wheel bearing on TOYOTA Yaris Hatchback (_P13_) – replacement guide

Free download PDF
3.71 MB
How to change front brake pads on TOYOTA Yaris Hatchback (_P13_) – replacement guide

Free download PDF
1.57 MB
How to change rear brake pads on TOYOTA Yaris Hatchback (_P13_) – replacement guide

Free download PDF
1.6 MB
How to change front brake discs on TOYOTA Yaris Hatchback (_P13_) – replacement guide

Free download PDF
1.93 MB
How to change rear brake discs on TOYOTA Yaris Hatchback (_P13_) – replacement guide

Free download PDF
1.96 MB

How to change front wheel bearing on Toyota Yaris Mk2 – replacement guide

Free download PDF
3.78 MB
How to change rear wheel bearing on Toyota Yaris Mk2 – replacement guide

Free download PDF
2.64 MB
How to change front wheel bearing on Toyota Yaris P1 – replacement guide

Free download PDF
2.53 MB
How to change rear wheel bearing on Toyota Yaris P1 – replacement guide

Free download PDF
1.13 MB
How to change front wheel bearing on TOYOTA Yaris III Hatchback (XP13) – replacement guide

Free download PDF
3.91 MB
How to change front wheel bearing on TOYOTA Yaris Hatchback (_P13_) – replacement guide

Free download PDF
3.71 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to restore wheel rims | AUTODOC tips

6K views

Published on: 13/05/2021
5 car interior cleaning mistakes | AUTODOC tips

6K views

Published on: 26/05/2022
5 tools that make car repair incredibly simple | AUTODOC tips

36K views

Published on: 25/01/2024
DIY car soundproofing | AUTODOC tips

76K views

Published on: 15/04/2021