Disclaimer
How to change rear wheel bearing on AUDI A3 Hatchback (8P1) – replacement guide
downloads:
2
Views:
20
Important!
This replacement procedure can be used for:
AUDI A3 Hatchback (8P1) 1.6 E-Power, AUDI A3 Hatchback (8P1) 2.0 FSI, AUDI A3 Hatchback (8P1) 1.6, AUDI A3 Hatchback (8P1) 2.0 TDI 16V, AUDI A3 Hatchback (8P1) 1.9 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 1.6 FSI, AUDI A3 Hatchback (8P1) 2.0 TFSI, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 1.8 TFSI, AUDI A3 Hatchback (8P1) 1.4 TFSI, AUDI A3 Hatchback (8P1) 1.6 TDI, AUDI A3 Hatchback (8P1) 1.6 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI … View more
The steps may slightly vary depending on the car design.
AUDI A3 Hatchback (8P1) 1.6 E-Power, AUDI A3 Hatchback (8P1) 2.0 FSI, AUDI A3 Hatchback (8P1) 1.6, AUDI A3 Hatchback (8P1) 2.0 TDI 16V, AUDI A3 Hatchback (8P1) 1.9 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 1.6 FSI, AUDI A3 Hatchback (8P1) 2.0 TFSI, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 1.8 TFSI, AUDI A3 Hatchback (8P1) 1.4 TFSI, AUDI A3 Hatchback (8P1) 1.6 TDI, AUDI A3 Hatchback (8P1) 1.6 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for A3 Hatchback (8P1) and other AUDI models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Brake cleaner
Copper grease
Combination spanner #13
Combination spanner #15
XZN socket bit # 14
XZN socket bit # 16
Torx bit T30
Drive socket # 13
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Rubber mallet
Crow bar
Wheel chock
Replacement: wheel bearing – AUDI A3 (8P1). Professionals recommend:
- Do not re-use the bearing assembly of your AUDI A3 (8P1) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- Warning! Shut down the engine before starting any work – AUDI A3 (8P1).
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. AUDI A3 (8P1) - Step 5
Remove the wheel. - Step 6
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the brake caliper fastening. Use a combination spanner #13. Use a combination spanner #15. - Step 8
Spread the brake pads. Use a crowbar. - Step 9
Remove the brake caliper. Use a crowbar.Replacement: wheel bearing – AUDI A3 (8P1). AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary. - Step 10
Remove the brake pads. - Step 11
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray. - Step 12
Unscrew the caliper bracket fastening. Use XZN #14. Use a tap wrench. Use a ratchet wrench. - Step 13
Remove the caliper bracket. - Step 14
Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray. - Step 15
Unscrew the brake disc fastening. Use Torx T30. Use a ratchet wrench. - Step 16
Remove the brake disc. - Step 17
Remove the hub bearing protection cap. Use a crowbar. Use a rubber mallet.Replacement: wheel bearing – AUDI A3 (8P1). AUTODOC experts recommend:Some cars are not equipped with wheel hub caps. - Step 18
Unscrew the wheel hub axle nut. Use XZN #16. Use a tap wrench. - Step 19
Remove the fastening bolt. - Step 20
Remove the hub and the bearing together, since they are a sealed unit. - Step 21
Clean the hub bearing mounting seat. Use all-purpose cleaning spray. - Step 22
Install the new wheel hub with a bearing. - Step 23
Install the fastening bolt.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A3 Hatchback (8P1) model
Popular maintenance tutorials for Audi A3 8P
Complete guides for changing the Wheel bearings on different AUDI A3 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A3 Hatchback (8P1)
View more
TOP 6 WD-40 lifehacks | AUTODOC tips
Motorcycle fuel tank restoration
Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips
Revive Your Vehicle's Look | How to Restore Wheel Rims Yourself!
Most commonly replaced car parts on AUDI A3
Time to replace parts? Get even better deals in our Shop app.

SCAN ME


































