
Disclaimer
How to change rear strut mount on AUDI A3 Hatchback (8P1) – replacement guide
downloads:
4
Views:
29
Important!
This replacement procedure can be used for:
AUDI A3 Hatchback (8P1) 1.6 E-Power, AUDI A3 Hatchback (8P1) 1.6, AUDI A3 Hatchback (8P1) 2.0 TDI 16V, AUDI A3 Hatchback (8P1) 1.9 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 3.2 V6 quattro, AUDI A3 Hatchback (8P1) 2.0 TDI quattro, AUDI A3 Hatchback (8P1) 2.0 TFSI, AUDI A3 Hatchback (8P1) 2.0 TFSI quattro, AUDI A3 Hatchback (8P1) 2.0 TDI 16V quattro, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI quattro, AUDI A3 Hatchback (8P1) S3 quattro, AUDI A3 Hatchback (8P1) 2.0 TDI quattro, AUDI A3 Hatchback (8P1) 1.8 TFSI, AUDI A3 Hatchback (8P1) 1.4 TFSI, AUDI A3 Hatchback (8P1) S3 quattro, AUDI A3 Hatchback (8P1) 1.8 TFSI quattro … View more
The steps may slightly vary depending on the car design.
AUDI A3 Hatchback (8P1) 1.6 E-Power, AUDI A3 Hatchback (8P1) 1.6, AUDI A3 Hatchback (8P1) 2.0 TDI 16V, AUDI A3 Hatchback (8P1) 1.9 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 3.2 V6 quattro, AUDI A3 Hatchback (8P1) 2.0 TDI quattro, AUDI A3 Hatchback (8P1) 2.0 TFSI, AUDI A3 Hatchback (8P1) 2.0 TFSI quattro, AUDI A3 Hatchback (8P1) 2.0 TDI 16V quattro, AUDI A3 Hatchback (8P1) 2.0 TDI, AUDI A3 Hatchback (8P1) 2.0 TDI quattro, AUDI A3 Hatchback (8P1) S3 quattro, AUDI A3 Hatchback (8P1) 2.0 TDI quattro, AUDI A3 Hatchback (8P1) 1.8 TFSI, AUDI A3 Hatchback (8P1) 1.4 TFSI, AUDI A3 Hatchback (8P1) S3 quattro, AUDI A3 Hatchback (8P1) 1.8 TFSI quattro … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Strut Mount for A3 Hatchback (8P1) and other AUDI models
Top strut mount
Alternative products

Wire brush
WD-40 spray
Copper grease
Drive socket # 14
Drive socket # 15
Drive socket # 18
Drive socket # 21
Combination spanner #14
Combination spanner #18
Combination spanner #21
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Vice
Hydraulic transmission jack
Wheel chock
Replacement: strut mount – AUDI A3 (8P1). AUTODOC recommends:
- The replacement procedure is identical for the mounts of the right and left shock absorbers of the rear suspension.
- Both mounts of the rear shock struts should be replaced simultaneously.
- All work should be done with the engine stopped.
Replacement: strut mount – AUDI A3 (8P1). Take the following steps:
- Step 1Secure the wheels with chocks.
- Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the rear of the car and secure on supports.Step 4Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. AUDI A3 (8P1)Step 5Remove the wheel.
- Step 6Support the arm. Use a hydraulic transmission jack.
- Step 7Unscrew the fastener connecting the control arm to the rear knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
- Step 8Lower the hydraulic transmission jack by 10-15 cm.Replacement: strut mount – AUDI A3 (8P1). Tip from AUTODOC experts:Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
- Step 9Remove the spring.
- Step 10Unscrew the lower fastener of the shock absorber. Use a drive socket #21. Use a tap wrench.
- Step 11Unscrew the upper fastener of the shock absorber. Use a drive socket #15. Use a ratchet wrench.Replacement: strut mount – AUDI A3 (8P1). Tip:To avoid injuries, hold the shock absorber when undoing the fastening bolts.
- Step 12Remove the shock absorber.Step 13Grip the shock absorber in a vice.
- Step 14Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray.
- Step 15Remove the shock absorber piston rod fastening. Use a combination spanner #14.
- Step 16Remove the shock absorber mount, boot and bump stop.
- Step 17Install the new mount, boot, and bump stop on the shock absorber.
- Step 18Fix the shock absorber mount. Use a combination spanner #14. Use a drive socket #14. Use a torque wrench. Tighten it to 25 Nm torque.
- Step 19Release the vice and take out the shock absorber.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A3 Hatchback (8P1) model
Popular maintenance tutorials for Audi A3 8P
Complete guides for changing the Strut mount on different AUDI A3 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A3 Hatchback (8P1)
View more
- Understanding Airbag Light Warnings | Essential Tips for Car Safety
- Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide
- Unveiling the secrets: Detecting vacuum leaks with a Smoke Machine | AUTODOC
- #TPMS Explained: Why Your Light is On and How to Respond Safely
Most commonly replaced car parts on AUDI A3
Time to replace parts? Get even better deals in our Shop app.

SCAN ME