Important!

This replacement procedure can be used for:
AUDI A3 Convertible (8P7) 1.2 TFSI, AUDI A3 Convertible (8P7) 2.0 TDI, AUDI A3 Convertible (8P7) 1.6 TDI, AUDI A3 Convertible (8P7) 1.6, AUDI A3 Convertible (8P7) 2.0 TDI, AUDI A3 Convertible (8P7) 1.9 TDI, AUDI A3 Convertible (8P7) 2.0 TFSI, AUDI A3 Convertible (8P7) 1.8 TFSI, AUDI A3 Convertible (8P7) 1.4 TFSI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Replacement: wheel bearing – AUDI A3 Convertible (8P7). List of the tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        All-purpose cleaning spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Combination spanner #13
                      
                        Combination spanner #15
                      
                        XZN socket bit # 14 
                      
                        XZN socket bit # 16 
                      
                        Torx bit T30
                      
                        Drive socket # 13 
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Tap wrench
                      
                        Rubber mallet
                      
                        Crow bar
                      
                        Wheel chock

Buy tools

Replacement: wheel bearing – AUDI A3 Convertible (8P7). Professionals recommend:

Do not re-use the bearing assembly of your AUDI A3 Convertible (8P7) car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
Warning! Shut down the engine before starting any work – AUDI A3 Convertible (8P7).

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. AUDI A3 Convertible (8P7)
Step 5

Remove the wheel.
Step 6

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the brake caliper fastening. Use a combination spanner #13. Use a combination spanner #15.
Step 8

Spread the brake pads. Use a crowbar.
Step 9

Remove the brake caliper. Use a crowbar.

Replacement: wheel bearing – AUDI A3 Convertible (8P7). AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 10

Remove the brake pads.
Step 11

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 12

Unscrew the caliper bracket fastening. Use XZN #14. Use a tap wrench. Use a ratchet wrench.
Step 13

Remove the caliper bracket.
Step 14

Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
Step 15

Unscrew the brake disc fastening. Use Torx T30. Use a ratchet wrench.
Step 16

Remove the brake disc.
Step 17

Remove the hub bearing protection cap. Use a crowbar. Use a rubber mallet.

Replacement: wheel bearing – AUDI A3 Convertible (8P7). AUTODOC experts recommend:
Some cars are not equipped with wheel hub caps.
Step 18

Unscrew the wheel hub axle nut. Use XZN #16. Use a tap wrench.
Step 19

Remove the fastening bolt.
Step 20

Remove the hub and the bearing together, since they are a sealed unit.
Step 21

Clean the hub bearing mounting seat. Use all-purpose cleaning spray.
Step 22

Install the new wheel hub with a bearing.
Step 23

Install the fastening bolt.
Step 24

Tighten the hub. Use XZN #16. Use a torque wrench. Tighten it to 180 Nm torque.+180°

Replacement: wheel bearing – AUDI A3 Convertible (8P7). Tip:
Important! Be sure to use new fasteners.The wheel bearing unit must not tilt on the axle pin.
Step 25

Install the hub bearing protection cap. Use a rubber mallet.
Step 26

Treat the hub where it contacts the brake disk. Use copper grease.
Step 27

Install the brake disc.
Step 28

Tighten the brake disc fastening. Use Torx T30. Use a torque wrench. Tighten it to 4 nm torque.
Step 29

Install the brake caliper bracket.
Step 30

Tighten the brake caliper bracket. Use XZN #14. Use a torque wrench. Tighten it to 90 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 31

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – AUDI A3 Convertible (8P7). After applying the spray, wait a few minutes.
Step 32

Install the brake pads.
Step 33

Install the brake caliper and fix it. Use a combination spanner #13. Use a drive socket #13. Use a torque wrench. Tighten it to 35 Nm torque.
Step 34

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 35

Clean the brake disk surface. Use a brake cleaner.

Replacement: wheel bearing – AUDI A3 Convertible (8P7). Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 36

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. AUDI A3 Convertible (8P7)
Step 37

Screw in the wheel bolts. Use wheel impact socket #17.
Step 38

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 39

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the AUDI A3 Convertible (8P7) model.

Browse tyres

How to change rear suspension lower trailing arm on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.66 MB
How to change front lower arm on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.89 MB
How to change front strut mount on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
2.95 MB
How to change rear suspension lower control arm on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.62 MB
How to change track rod end on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.47 MB
How to change rear anti roll bar links on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.37 MB

How to change rear wheel bearing on Audi A3 8PA – replacement guide

Free download PDF
2.1 MB
How to change front wheel bearing on AUDI A3 Sportback (8PA) – replacement guide

Free download PDF
2.5 MB
How to change rear wheel bearing on AUDI A3 Hatchback (8P1) – replacement guide

Free download PDF
2.05 MB
How to change front wheel bearing on AUDI A3 Hatchback (8P1) – replacement guide

Free download PDF
2.5 MB
How to change front wheel bearing on AUDI A3 Sportback (8VA, 8VF) – replacement guide

Free download PDF
2.5 MB
How to change front wheel bearing on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
2.49 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

5 Tips for New Drivers | AUTODOC tips

3K views

Published on: 31/01/2023
How to detect vacuum leaks using a smoke machine | AUTODOC

19K views

Published on: 23/07/2020
DIY car soundproofing | AUTODOC tips

76K views

Published on: 15/04/2021
How to start a car after a long idle period | AUTODOC tips

6K views

Published on: 20/05/2021