Important!

This replacement procedure can be used for:
AUDI A3 Convertible (8P7) 1.4 TFSI, AUDI A3 Convertible (8P7) 1.8 TFSI, AUDI A3 Convertible (8P7) 2.0 TFSI, AUDI A3 Convertible (8P7) 1.9 TDI, AUDI A3 Convertible (8P7) 2.0 TDI, AUDI A3 Convertible (8P7) 1.6, AUDI A3 Convertible (8P7) 1.6 TDI, AUDI A3 Convertible (8P7) 2.0 TDI, AUDI A3 Convertible (8P7) 1.2 TFSI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – AUDI A3 Convertible (8P7). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Combination spanner #14
                    
                      Combination spanner #16
                    
                      HEX bit No.H5.
                    
                      XZN socket bit # 6 
                    
                      Drive socket # 14 
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: anti roll bar links – AUDI A3 Convertible (8P7). AUTODOC recommends:

Replace the stabiliser links on AUDI A3 Convertible (8P7) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
All work should be done with the engine stopped.

Replacement: anti roll bar links – AUDI A3 Convertible (8P7). Use the following procedure:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: anti roll bar links – AUDI A3 Convertible (8P7). Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
Step 8

Unscrew the fasteners connecting the stabiliser link to the stabiliser bar. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
Step 9

Remove the stabilizer rod.

Replacement: anti roll bar links – AUDI A3 Convertible (8P7). Tip from AUTODOC experts:
Examine stabiliser bushes. Replace them if needed.
Step 10

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 11

Ιnstall the transverse stabilizer link.
Step 12

Tighten the stabiliser link fastener. Use a combination spanner #14. Use HEX No.H5. Use a ratchet wrench.
Step 13

Tighten the fastener connecting the stabilizer bar with the control arm. Use a drive socket #14. Use a torque wrench. Tighten it to 45 Nm torque.
Step 14

Support the arm. Use a hydraulic transmission jack.
Step 15

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #14. Use a torque wrench. Tighten it to 45 Nm torque.
Step 16

Remove the support from under the arm.

AUTODOC recommends:
Replacement: anti roll bar links – AUDI A3 Convertible (8P7). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 17

Treat all joints of the stabiliser link. Use copper grease.
Step 18

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 19

Clean the brake disk surface. Use a brake cleaner.

Replacement: anti roll bar links – AUDI A3 Convertible (8P7). AUTODOC experts recommend:
After applying the spray, wait a few minutes.
Step 20

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. AUDI A3 Convertible (8P7)
Step 21

Screw in the wheel bolts. Use wheel impact socket #17.
Step 22

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 120 Nm torque.
Step 23

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the AUDI A3 Convertible (8P7) model

Audi A3 Convertible tyre size

How to change rear suspension lower trailing arm on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.66 MB
How to change rear wheel bearing on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
2.05 MB
How to change front lower arm on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.89 MB
How to change front strut mount on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
2.95 MB
How to change rear suspension lower control arm on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.62 MB
How to change track rod end on AUDI A3 Convertible (8P7) – replacement guide

Free download PDF
1.47 MB

How to change front anti roll bar links on Audi A3 8PA – replacement guide

Free download PDF
1.26 MB
How to change rear anti roll bar links on Audi A3 8PA – replacement guide

Free download PDF
1.35 MB
How to change front anti roll bar links on AUDI A3 Hatchback (8P1) – replacement guide

Free download PDF
1.15 MB
How to change rear anti roll bar links on AUDI A3 Hatchback (8P1) – replacement guide

Free download PDF
1.37 MB
How to change front anti roll bar links on AUDI A3 Sportback (8VA, 8VF) – replacement guide

Free download PDF
1.22 MB
How to change rear anti roll bar links on AUDI A3 Sportback (8VA, 8VF) – replacement guide

Free download PDF
1.19 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

7 signs of faulty fuel injectors | AUTODOC tips

10K views

Published on: 09/01/2025
How to Prevent Premature Wear on Your Car Boot Damper | AUTODOC

5K views

Published on: 04/07/2021
Initial Car Inspection: What to Check Before You Buy

5K views

Published on: 24/10/2020
Why does it burn oil? The main cause of oil consumption in EA888 Gen 1

118K views

Published on: 14/08/2025