
Disclaimer
How to change rear wheel bearing on AUDI 90 B2 (81, 85) – replacement guide
downloads:
0
Views:
4
Important!
This replacement procedure can be used for:
AUDI 90 (81, 85, B2) 1.6 TD … View more
The steps may slightly vary depending on the car design.
AUDI 90 (81, 85, B2) 1.6 TD … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for 90 (81, 85, B2) and other AUDI models
Wheel bearing kit
Alternative products

Wire brush
All-purpose cleaning spray
Multipurpose grease
Copper grease
Torque wrench
Combination spanner #10
Drive socket # 24
Wheel impact socket #17
Bush and bearing driver set
3-Arm Gear Puller
Ratchet wrench
Hammer
Crow bar
Wheel chock
AUTODOC recommends:
- Do not re-use the bearing assembly of your AUDI 90 (81, 85, B2) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- Please note: all work on the car – AUDI 90 (81, 85, B2) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Engage the parking brake lever.
- Step 2Loosen the parking brake cable. Use a combination spanner #10.
- Step 3Secure the wheels with chocks.Step 4Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 5Raise the rear of the car and secure on supports.Step 6Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. AUDI 90 (81, 85, B2)
- Step 7Remove the wheel.
- Step 8Clean the brake drum. Use a wire brush. Use all-purpose cleaning spray.
- Step 9Remove the wheel hub nut cap. Use a crowbar. Use a hammer.
- Step 10Remove the cotter pin securing the hub nut. Use a crowbar. Use a hammer.
- Step 11Unscrew the hub nut. Use a drive socket #24. Use a ratchet wrench.
- Step 12Remove the brake drum assembled with the wheel hub bearing.Replacement: wheel bearing – AUDI 90 (81, 85, B2). Tip:Examine the brake drum. Replace it if necessary.
- Step 13Clean the hub bearing mounting seat. Use all-purpose cleaning spray.
- Step 14Remove the hub bearing mounting. Use a crowbar.
- Step 15Remove the inner oil seal of the wheel bearing. Use a crowbar.
- Step 16Remove the hub bearing mounting. Use a crowbar.
- Step 17Clean the hub bearing mounting seat.
- Step 18Remove the inner race of the wheel bearing from the brake drum. Use 3-Arm Gear Puller. Use a bush and bearing driver set.
- Step 19Remove the inner race of the wheel bearing from the brake drum. Use a bush and bearing driver set.
- Step 20Install the new inner race of the wheel bearing into the brake drum. Use a bush and bearing driver set. Use a hammer.
- Step 21Install the new inner race of the wheel bearing into the brake drum. Use a bush and bearing driver set. Use a hammer.
- Step 22Treat the inner race and the wheel bearing. Use a multipurpose grease.
- Step 23Install a new hub bearing and secure it.
- Step 24Press in the inner oil seal of the wheel bearing. Use a bush and bearing driver set. Use a hammer.
- Step 25Install a new hub bearing and secure it.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI 90 B2 (81, 85) model
Popular maintenance tutorials for Audi 90 B2
Complete guides for changing the Wheel bearings on different AUDI 90 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI 90 (81, 85, B2)
View more
- How to Make a DIY Foam Sprayer | AUTODOC tips
- How to make an injector test bench yourself
- Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips
- Top Automatic Transmission Blunders You Must Dodge | AUTODOC Insights
Most commonly replaced car parts on AUDI 90
Time to replace parts? Get even better deals in our Shop app.

SCAN ME