Disclaimer
How to change rear wheel bearing on ABARTH 500 / 595 / 695 Hatchback (312) – replacement guide
downloads:
12
Views:
156
Important!
This replacement procedure can be used for:
ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXF1A, 312.AXD1A), ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXF11, 312.AXF1A, 312.AXD1A), ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXD1A), ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXT1A), ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXF11, 312.AXF1A) … View more
The steps may slightly vary depending on the car design.
ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXF1A, 312.AXD1A), ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXF11, 312.AXF1A, 312.AXD1A), ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXD1A), ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXT1A), ABARTH 500 / 595 / 695 Hatchback (312_) 1.4 (312.AXF11, 312.AXF1A) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for 500 / 595 / 695 Hatchback (312_) and other ABARTH models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
All-purpose cleaning spray
Copper grease
Drive socket # 12
Drive socket # 13
Drive socket # 17
Drive socket # 32
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Hammer
Rubber mallet
Crow bar
Wheel chock
Replacement: wheel bearing – ABARTH 500 / 595 (312_). AUTODOC experts recommend:
- Do not re-use the bearing assembly of your ABARTH 500 / 595 (312_) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- All work should be done with the engine stopped.
Replacement: wheel bearing – ABARTH 500 / 595 (312_). Use the following procedure:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. ABARTH 500 / 595 (312_) - Step 5
Remove the wheel. - Step 6
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the brake caliper fastening. Use a drive socket #13. Use a ratchet wrench. - Step 8
Remove the brake caliper. Use a crowbar.Replacement: wheel bearing – ABARTH 500 / 595 (312_). AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. - Step 9
Remove the brake pads. - Step 10
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray. - Step 11
Unscrew the caliper bracket fastening. Use a drive socket #17. Use a tap wrench. - Step 12
Remove the caliper bracket. - Step 13
Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray. - Step 14
Unscrew the brake disc fastening. Use a drive socket #12. Use a ratchet wrench. - Step 15
Remove the brake disc. Use a rubber mallet. - Step 16
Remove the hub bearing protection cap. Use a crowbar. Use a hammer.Replacement: wheel bearing – ABARTH 500 / 595 (312_). Tip from AUTODOC experts:Some cars are not equipped with wheel hub caps. - Step 17
Unscrew the wheel hub axle nut. Use a drive socket #32. Use a tap wrench. - Step 18
Remove the hub and the bearing together, since they are a sealed unit. - Step 19
Clean the hub bearing mounting seat. Use all-purpose cleaning spray. - Step 20
Install the new wheel hub with a bearing. - Step 21
Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 224 Nm torque.Replacement: wheel bearing – ABARTH 500 / 595 (312_). Tip:The wheel bearing unit must not tilt on the axle pin. - Step 22
Install the hub bearing protection cap. Use a rubber mallet.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the ABARTH 500 / 595 / 695 Hatchback (312) model
Popular maintenance tutorials for Abarth 595
Complete guides for changing the Wheel bearings on different ABARTH 500 / 595 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your ABARTH 500 / 595 / 695 Hatchback (312_)
View more
Revive Your Tyres: Expert Tips for a Lasting Shine | AUTODOC Guide
Fuse Replacement Made Simple: Step-by-Step Guide | AUTODOC
Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips
Don’t Replace, Restore: Fixing Damaged Threads at Home
Most commonly replaced car parts on ABARTH 500 / 595
Professional manuals for the most common ABARTH models
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
























