Disclaimer
How to change rear strut mount on FORD Focus Mk2 Hatchback (DA_, HCP, DP) – replacement guide
downloads:
1
Views:
30
Important!
This replacement procedure can be used for:
FORD Focus II Hatchback (DA_, HCP, DP) 1.6 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 1.6, FORD Focus II Hatchback (DA_, HCP, DP) 1.6 Ti, FORD Focus II Hatchback (DA_, HCP, DP) 2.0, FORD Focus II Hatchback (DA_, HCP, DP) 1.4, FORD Focus II Hatchback (DA_, HCP, DP) 1.6 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 2.0 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 1.6 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 1.8 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 2.5 ST, FORD Focus II Hatchback (DA_, HCP, DP) 1.8 Flexifuel, FORD Focus II Hatchback (DA_, HCP, DP) 2.0 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 1.8, FORD Focus II Hatchback (DA_, HCP, DP) 2.5 RS, FORD Focus II Hatchback (DA_, HCP, DP) 2.0 CNG, FORD Focus II Hatchback (DA_, HCP, DP) 2.0 LPG, FORD Focus II Hatchback (DA_, HCP, DP) 1.6 LPG, FORD Focus II Hatchback (DA_, HCP, DP) 2.5 RS 500 … View more
The steps may slightly vary depending on the car design.
FORD Focus II Hatchback (DA_, HCP, DP) 1.6 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 1.6, FORD Focus II Hatchback (DA_, HCP, DP) 1.6 Ti, FORD Focus II Hatchback (DA_, HCP, DP) 2.0, FORD Focus II Hatchback (DA_, HCP, DP) 1.4, FORD Focus II Hatchback (DA_, HCP, DP) 1.6 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 2.0 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 1.6 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 1.8 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 2.5 ST, FORD Focus II Hatchback (DA_, HCP, DP) 1.8 Flexifuel, FORD Focus II Hatchback (DA_, HCP, DP) 2.0 TDCi, FORD Focus II Hatchback (DA_, HCP, DP) 1.8, FORD Focus II Hatchback (DA_, HCP, DP) 2.5 RS, FORD Focus II Hatchback (DA_, HCP, DP) 2.0 CNG, FORD Focus II Hatchback (DA_, HCP, DP) 2.0 LPG, FORD Focus II Hatchback (DA_, HCP, DP) 1.6 LPG, FORD Focus II Hatchback (DA_, HCP, DP) 2.5 RS 500 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Strut Mount for Focus II Hatchback (DA_, HCP, DP) and other FORD models
Alternative products

Wire brush
WD-40 spray
Copper grease
Drive socket # 10
Drive socket # 13
Drive socket # 16
Combination spanner #13
Combination spanner #16
Ratchet wrench
Torque wrench
Adjustable wrench
Vice
Wheel impact socket #19
Hydraulic transmission jack
Wheel chock
Replacement: strut mount – FORD FOCUS II (DA_). Tip from AUTODOC experts:
- The replacement procedure is identical for the mounts of the right and left shock absorbers of the rear suspension.
- Both mounts of the rear shock struts should be replaced simultaneously.
- All work should be done with the engine stopped.
Replacement: strut mount – FORD FOCUS II (DA_). Take the following steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: strut mount – FORD FOCUS II (DA_). AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Support the arm. Use a hydraulic transmission jack. - Step 7
Clean the fasteners of the shock absorber upper mount. Use a wire brush. Use WD-40 spray. - Step 8
Unscrew the shock absorber mount fastening. Use a drive socket #10. Use a ratchet wrench. - Step 9
Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray. - Step 10
Unscrew the lower fastener of the shock absorber. Use a drive socket #16. Use a ratchet wrench. Use a tap wrench.AUTODOC recommends:Important! Hold the shock absorber while unscrewing the fastening bolts. FORD FOCUS II (DA_) - Step 11
Remove the shock absorber. - Step 12
Grip the shock absorber in a vice. - Step 13
Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray. - Step 14
Remove the shock absorber piston rod fastening. Use a combination spanner #13. - Step 15
Remove the shock absorber mount, boot and bump stop. - Step 16
Install the new mount, boot, and bump stop on the shock absorber. - Step 17
Screw the shock strut piston rod upper fastening. Use a combination spanner #13. Use a drive socket #13. Use an adjustable wrench. Use a torque wrench. Tighten it to 25 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the FORD Focus Mk2 Hatchback (DA_, HCP, DP) model
Popular maintenance tutorials for Ford Focus Mk2
Complete guides for changing the Strut mount on different FORD FOCUS models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your FORD Focus II Hatchback (DA_, HCP, DP)
View more
Don’t Replace, Just Polish! Headlight Restoration with AUTODOC
Reviving Your Car: How to Start After Extended Idle Time | AUTODOC Tips
Top 5 reasons why your car squeals | AUTODOC Tips
DIY engine block coffee table
Most commonly replaced car parts on FORD FOCUS
Time to replace parts? Get even better deals in our Shop app.

SCAN ME































