Disclaimer
How to change rear brake pads on FORD C-Max II (DXA/CB7, DXA/CEU) – replacement guide
downloads:
17
Views:
278
Recommended replacement interval for the part category Brake pad set : 30000 km
Important!
This replacement procedure can be used for:
FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Ti, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Ti, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 EcoBoost, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 EcoBoost, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Flexifuel, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Ti, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 LPG, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 LPG, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Ti … View more
The steps may slightly vary depending on the car design.
FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Ti, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Ti, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 EcoBoost, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 EcoBoost, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Flexifuel, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Ti, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 LPG, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 LPG, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 2.0 TDCi, FORD C-Max II (DXA/CB7, DXA/CEU) 1.6 Ti … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Pads for C-Max II (DXA/CB7, DXA/CEU) and other FORD models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Anti-squeal paste
Brake caliper guide pins grease
Copper grease
HEX bit no.H7.
Wheel impact socket #19
Ratchet wrench
Torque wrench
Brake caliper wind back tool
Flat Screwdriver
Crow bar
Wheel chock
Replacement: brake pads – FORD C-MAX II. AUTODOC recommends:
- Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
- The replacement procedure is identical for all brake pads on the same axle.
- All work should be done with the engine stopped.
Replacement: brake pads – FORD C-MAX II. Use the following procedure:
- Step 1Open the bonnet. Unscrew the brake fluid reservoir cap.Step 2
Secure the wheels with chocks. - Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 4Raise the rear of the car and secure on supports.Step 5
Unscrew the wheel bolts.Replacement: brake pads – FORD C-MAX II. Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 6
Remove the wheel. - Step 7
Detach the brake caliper retaining spring. Use a flat screwdriver. - Step 8
Remove the dust boot caps of the brake caliper guide pins. Use a flat screwdriver. - Step 9
Unscrew the brake caliper fastening. Use HEX No.H7. Use a ratchet wrench. - Step 10Remove the guide pins from the brake caliper.Step 11
Spread the brake pads. Use a crowbar. - Step 12
Remove the brake caliper.Replacement: brake pads – FORD C-MAX II. AUTODOC experts recommend:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary. - Step 13
Remove the brake pads.Replacement: brake pads – FORD C-MAX II. Tip from AUTODOC:Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced. - Step 14
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.AUTODOC recommends:Replacement: brake pads – FORD C-MAX II. After applying the spray, wait a few minutes. - Step 15
Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.Replacement: brake pads – FORD C-MAX II. Tip from AUTODOC experts:Make sure the disc surface is clean before installing the pads. - Step 16
Install new brake pads.Replacement: brake pads – FORD C-MAX II. Tip:Make sure the pads are installed with linings facing the disc. - Step 17Treat the brake caliper piston. Use a brake cleaner.AUTODOC recommends:Replacement: brake pads – FORD C-MAX II. After applying the spray, wait a few minutes.Step 18
Press in the brake caliper piston. Use brake caliper wind back tool. - Step 19
Install the brake caliper and fix it.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the FORD C-Max II (DXA/CB7, DXA/CEU) model
Popular maintenance tutorials for Ford C Max 2
Complete guides for changing the Brake pad set on different FORD C-MAX models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your FORD C-Max II (DXA/CB7, DXA/CEU)
View more
CHECK ENGINE light turned on – step-by-step guide on what to do
Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide
5 signs of a faulty strut mount and how to fix it
DIY alternator repair | AUTODOC tips
Most commonly replaced car parts on FORD C-MAX
Time to replace parts? Get even better deals in our Shop app.

SCAN ME



































