Disclaimer
How to change lambda sensor on OPEL Corsa B Hatchback (S93) – replacement guide
downloads:
61
Views:
1523
Recommended replacement interval for the part category Lambda sensor : 100000 km
Important!
This replacement procedure can be used for:
OPEL Corsa B Hatchback (S93) 1.6 i 16V (F08, F68, M68), OPEL Corsa B Hatchback (S93) 1.4 i 16V (F08, F68, M68), OPEL Corsa B Hatchback (S93) 1.2 i 16V (F08, F68, M68), OPEL Corsa B Hatchback (S93) 1.0 i 12V (F08, F68, M68) … View more
The steps may slightly vary depending on the car design.
OPEL Corsa B Hatchback (S93) 1.6 i 16V (F08, F68, M68), OPEL Corsa B Hatchback (S93) 1.4 i 16V (F08, F68, M68), OPEL Corsa B Hatchback (S93) 1.2 i 16V (F08, F68, M68), OPEL Corsa B Hatchback (S93) 1.0 i 12V (F08, F68, M68) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Lambda Sensor for Corsa B Hatchback (S93) and other OPEL models
Alternative products
Lambda sensor
Wire brush
WD-40 spray
Electronic spray
High-temperature ceramic grease
Torque wrench
Combination spanner #22
Flare nut wrench #22
Ratchet wrench
Thread tap
Fender cover
Replacement: lambda sensor – OPEL CORSA B (73_, 78_, 79_). AUTODOC experts recommend:
- After replacing the oxygen sensor, clear the trouble code from the electronic control unit and let the ECU adapt itself to the new sensor.
- Before getting down to work, start the engine and let it warm up to operating temperature.
- Please note: all work on the car – OPEL CORSA B (73_, 78_, 79_) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Lift the car using a jack or place it over an inspection pit.Step 4
Clean the oxygen sensor fastener. Use a wire brush. Use WD-40 spray. - Step 5
Detach the oxygen sensor connector. - Step 6
Unscrew the oxygen sensor fastener. Use a flare nut spanner #22. - Step 7
Remove the oxygen sensor. - Step 8
Cut the thread for the new oxygen sensor. Use a thread tap. Use a ratchet wrench. - Step 9Treat the oxygen sensor. Use high-temperature ceramic grease.Step 10
Install the new oxygen sensor.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 2
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the OPEL Corsa B Hatchback (S93) model
Popular maintenance tutorials for Opel Corsa S93
Free download PDF
1.25 MB
Free download PDF1013.76 KB
Free download PDF2.06 MB
Free download PDF993.28 KB
Free download PDF1.65 MB
Free download PDF2.1 MB
Complete guides for changing the Oxygen sensor on different OPEL CORSA models
Free download PDF829.44 KB
Free download PDF798.72 KB
Free download PDF819.2 KB
Free download PDF1 MB
Free download PDF1.16 MB
Free download PDF1.02 MB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your OPEL Corsa B Hatchback (S93)
View more
Top 7 Manual Transmission Mistakes to Avoid | AUTODOC Tips
Reviving Your Car: How to Start After Extended Idle Time | AUTODOC Tips
Revive Your Vehicle's Look | How to Restore Wheel Rims Yourself!
5 Essential Tips for beginner drivers: Avoid Common Mistakes
Most commonly replaced car parts on OPEL CORSA
Time to replace parts? Get even better deals in our Shop app.
SCAN ME
Thank you for the support, however, I am struggling to locate the oxygen sensor of a 2001 Corsa utility. The PDF is not really helpful. It looks like there's no enough videos on the internet on an Opel Corsa 2001 utility. Or Opel Corsa B