
Disclaimer
How to change ignition coil on NISSAN Micra III Hatchback (K12) – replacement guide
downloads:
11
Views:
339
Important!
This replacement procedure can be used for:
NISSAN MICRA III (K12) 160 SR … View more
The steps may slightly vary depending on the car design.
NISSAN MICRA III (K12) 160 SR … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Ignition Coil for MICRA III (K12) and other NISSAN models
Ignition coil
Alternative products

Electronic spray
Torque wrench
Drive socket # 8
Drive socket # 10
Ratchet wrench
Round-nose pliers
Flat screwdriver
Microfibre towel
Fender cover
Replacement: ignition coil – NISSAN MICRA III (K12). AUTODOC experts recommend:
- The replacement procedure is the same for the ignition coils of all cylinders.
- All work should be done with the engine stopped.
Replacement: ignition coil – NISSAN MICRA III (K12). Use the following procedure:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Disconnect the crankcase ventilation hose from the air duct. Use round-nose pliers.
- Step 4Unscrew the clamps and fasteners on the air filter intake pipe. Use a drive socket #10. Use a ratchet wrench.
- Step 5Disconnect the air intake pipe from the air filter housing.Step 6Unscrew the fasteners connecting the throttle valve to the intake manifold. Use a drive socket #8. Use a ratchet wrench.
- Step 7Release the clamp and detach the connector and the vacuum hose from the intake manifold near the throttle valve. Use round-nose pliers.
- Step 8Unscrew the fasteners of the intake manifold bracket. Use a drive socket #10.
- Step 9Detach the vacuum booster hose from the intake manifold.
- Step 10Unscrew the intake manifold fasteners. Use a drive socket #10. Use a ratchet wrench.
- Step 11Remove the intake manifold.
- Step 12Cover the intake manifold passages with a microfibre towel to prevent dust and dirt from getting inside.
- Step 13Detach the connector from the ignition coil.
- Step 14Unscrew the ignition coil bracket. Use a drive socket #10.
- Step 15Take out the ignition coil from the spark plug well.
- Step 16Clean dirt, dust and debris from inside the spark plug well.Step 17Install the new ignition coil to the spark plug well. Make sure you hear a click indicating that it is locked in place.
- Step 18Treat the ignition coil connector with electronic spray. The spray will protect the electrical contacts from corrosion, oxidation, and will reduce the contact resistance.Step 19Tighten the ignition coil fastening. Use a drive socket #10. Use a torque wrench. Tighten it to 7 nm torque.
- Step 20Plug in the ignition coil connector.
- Step 21Remove the microfibre towel from the intake manifold.
- Step 22Remove the intake manifold gasket. Use a flat screwdriver.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the NISSAN Micra III Hatchback (K12) model
Popular maintenance tutorials for Nissan Micra Mk3
Complete guides for changing the Coil pack on different NISSAN MICRA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your NISSAN MICRA III (K12)
View more
- How to Fix P0401 ✅ error code Insufficient EGR flow
- Reviving Your Car: How to Start After Extended Idle Time | AUTODOC Tips
- Top 5 mistakes when replacing spark plugs | AUTODOC tips
- DIY manual gearbox restoration | Drivetrain restoration – Part 3
Most commonly replaced car parts on NISSAN MICRA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME