Important!
This replacement procedure can be used for:
PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 D, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 DT, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.1, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.4, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.6, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.8, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 XSi, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 S16, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 S16, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 D, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 S16, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.8 16V, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 16V, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 D, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 D, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 HDI 90, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.8 D, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.6, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.8, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.6, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 D, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 D, PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.8 D View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for 306 Hatchback (7A, 7C, N3, N5) and other PEUGEOT models
Tools
Replacement: wheel bearing – PEUGEOT 306 Hatchback (7A, 7C, N3, N5). Tools you need:
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Sealant
Multipurpose grease
High-temperature ceramic grease
Torque wrench
Torx bit T55
Drive socket # 10
Drive socket # 16
Drive socket # 17
Drive socket # 21
Drive socket # 36
Wheel impact socket #19
Ratchet wrench
Tap wrench
Hammer
Pin punch
Crow bar
Phillips screwdriver
Flat Screwdriver
Round-nose pliers
Bearing separator
Ball joint puller
Bush and bearing driver set
Hydraulic transmission jack
Wheel chock
Replacement: wheel bearing – PEUGEOT 306 Hatchback (7A, 7C, N3, N5). Tip from AUTODOC:
  • Do not re-use the bearing assembly of your PEUGEOT 306 Hatchback (7A, 7C, N3, N5) car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – PEUGEOT 306 Hatchback (7A, 7C, N3, N5) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    Open the bonnet. Unscrew the brake fluid reservoir cap.
    Step 2
    How to change Wheel Bearing on Peugeot 306 7a 1993 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 3
    How to replace PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 HDI 90 1994 Wheel Bearing - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  3. Step 4
    Raise the front of the car and secure on supports.
    Step 5
    Peugeot 306 7a 1.4 1995 Wheel Bearing replacement: free workshop manuals
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. PEUGEOT 306 Hatchback (7A, 7C, N3, N5)
  4. Step 6
    Changing Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.6 1996 by yourself
    Remove the wheel.
  5. Step 7
    Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
    Step 8
    How to remove PEUGEOT 306 1.9 D 1997 Wheel Bearing - online easy-to-follow instructions
    Unscrew the brake caliper bracket fasteners. Use Torx T55. Use a tap wrench. Use a ratchet wrench.
  6. Step 9
    Remove the fastening bolts (2 pieces).
    Step 10
    How to replace Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1998: download PDF manuals and video instructions
    Disconnect the brake pad wear sensor plug.
  7. Step 11
    How hard is it to do yourself: Wheel Bearing replacement on Peugeot 306 7a 2.0 S16 1999 - download illustrated guide
    Remove the brake caliper together with its bracket.
    Replacement: wheel bearing – PEUGEOT 306 Hatchback (7A, 7C, N3, N5). Professionals recommend:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
  8. Step 12
    Need to know how to renew Wheel Bearing on PEUGEOT 306 2000? This free workshop manual will help you to do it yourself
    Take out the retainer clip and move the brake hose out of the bracket on the shock strut. Use round-nose pliers.
  9. Step 13
    Changing of Wheel Bearing on Peugeot 306 7a 2001 won't be an issue if you follow this illustrated step-by-step guide
    Disconnect the ABS sensor wiring. Use a crowbar.
  10. Step 14
    PEUGEOT 306 2.0 HDI 90 Wheel Bearing replacement: online guides and video tutorials
    Unscrew the ABS sensor wiring bracket. Use a drive socket #10. Use a ratchet wrench.
  11. Step 15
    Replacing Wheel Bearing on Peugeot 306 7a 2003 2.0 HDI 90 by yourself
    Remove the bracket from the suspension strut.
  12. Step 16
    306 Hatchback (7A, 7C, N3, N5) 1.9 D 1993 Wheel Bearing DIY replacement workshop manual
    Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
  13. Step 17
    How to change Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1994 - tips and tricks
    Unscrew the brake disc fasteners. Use a Phillips screwdriver.
  14. Step 18
    Step-by-step recommendations for DIY replacement Peugeot 306 7a 1995 1.9 D Wheel Bearing
    Remove the brake disc.
  15. Step 19
    DIY replacement of Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 DT 1996 is not an issue anymore with our step-by-step tutorial
    Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
  16. Step 20
    How to change Wheel Bearing on Peugeot 306 7a 1993 - free PDF and video manuals
    Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
  17. Step 21
    How to replace PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 HDI 90 1994 Wheel Bearing - step-by-step manuals and video guides
    Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
  18. Step 22
    Clean the fastener that connects the suspension arm to the ball joint. Use a wire brush. Use WD-40 spray.
    Step 23
    Peugeot 306 7a 1.4 1995 Wheel Bearing replacement: free workshop manuals
    Unscrew the fastener that connects the suspension arm to the steering knuckle. Use a drive socket #21. Use a ratchet wrench.
  19. Step 24
    Changing Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.6 1996 by yourself
    Disconnect the lower control arm from the steering knuckle. Use a ball joint puller. Use a crowbar.
  20. Step 25
    How to remove PEUGEOT 306 1.9 D 1997 Wheel Bearing - online easy-to-follow instructions
    Remove the cotter pin securing the hub nut. Use round-nose pliers. Use a flat screwdriver.
  21. Step 26
    Clean the wheel hub fastener. Use a wire brush. Use WD-40 spray.
    Step 27
    How to replace Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1998: download PDF manuals and video instructions
    Unscrew the wheel hub axle nut. Use a drive socket #36. Use a ratchet wrench.
  22. Step 28
    Remove the fastening nut.
    Step 29
    How hard is it to do yourself: Wheel Bearing replacement on Peugeot 306 7a 2.0 S16 1999 - download illustrated guide
    Detach the driveshaft from the steering knuckle. Use a pin punch. Use a hammer.
  23. Step 30
    Need to know how to renew Wheel Bearing on PEUGEOT 306 2000? This free workshop manual will help you to do it yourself
    Unscrew the fastener connecting the ABS sensor to the steering knuckle. Use a drive socket #10. Use a ratchet wrench.
  24. Step 31
    Changing of Wheel Bearing on Peugeot 306 7a 2001 won't be an issue if you follow this illustrated step-by-step guide
    Remove the ABS sensor from the steering knuckle.
  25. Step 32
    Clean the lower fastener connecting the suspension strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
    Step 33
    PEUGEOT 306 2.0 HDI 90 Wheel Bearing replacement: online guides and video tutorials
    Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #16. Use a ratchet wrench.
  26. Step 34
    Remove the fastening bolt.
    Step 35
    Disconnect the steering knuckle from the shock absorber strut. Use a hammer.
    Step 36
    Replacing Wheel Bearing on Peugeot 306 7a 2003 2.0 HDI 90 by yourself
    Remove the steering knuckle together with the hub.
  27. Step 37
    306 Hatchback (7A, 7C, N3, N5) 1.9 D 1993 Wheel Bearing DIY replacement workshop manual
    Remove the wheel hub from the steering knuckle. Use a bush and bearing driver set. Use a hammer.
  28. Step 38
    How to change Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1994 - tips and tricks
    Remove the wheel hub bearing retaining ring. Use round-nose pliers.
  29. Step 39
    Step-by-step recommendations for DIY replacement Peugeot 306 7a 1995 1.9 D Wheel Bearing
    Press out the wheel hub bearing. Use a bush and bearing driver set.
  30. Step 40
    Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
    Step 41
    Treat the mounting seat of the bearing assembly. Use a multipurpose grease.
    Step 42
    DIY replacement of Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 DT 1996 is not an issue anymore with our step-by-step tutorial
    Press the new bearing in the steering knuckle. Use a bush and bearing driver set.
    AUTODOC recommends:
    Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
  31. Step 43
    How to change Wheel Bearing on Peugeot 306 7a 1993 - free PDF and video manuals
    Install the retaining ring on the steering knuckle. Use round-nose pliers.
  32. Step 44
    Dismantle the inner bearing race that is remaining on the hub. Use a bush and bearing driver set. Use a bearing separator.
    Step 45
    Treat the wheel hub mounting seat. Use a multipurpose grease.
    Step 46
    How to replace PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 2.0 HDI 90 1994 Wheel Bearing - step-by-step manuals and video guides
    Install the wheel hub on the steering knuckle. Use a bush and bearing driver set.
  33. Step 47
    Peugeot 306 7a 1.4 1995 Wheel Bearing replacement: free workshop manuals
    Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
  34. Step 48
    Changing Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.6 1996 by yourself
    Install the steering knuckle with a hub in assembly.
  35. Step 49
    How to remove PEUGEOT 306 1.9 D 1997 Wheel Bearing - online easy-to-follow instructions
    Support the steering knuckle.
  36. Step 50
    How to replace Wheel Bearing on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1998: download PDF manuals and video instructions
    Fix the shock absorber strut on the steering knuckle. Use a hammer.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT 306 Hatchback model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
PEUGEOT 306 Hatchback (7A, 7C, N3, N5) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
Autodoc CLUB App icon
DIY PEUGEOT 306 Hatchback (7A, 7C, N3, N5) Wheel Bearing replacement - online guide
Tips & tricks for your PEUGEOT 306 Hatchback (7A, 7C, N3, N5)
View more
  • How to change Wheel bearings on PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.9 DT - replacement tricks
    Top Automatic Transmission Blunders You Must Dodge | AUTODOC Insights
  • Changing Hub bearing Peugeot 306 7a 2.0 HDI 90 - Replacement Tips
    DIY car soundproofing | AUTODOC tips
  • Maintenance Hacks - PEUGEOT 306 Hatchback (7A, 7C, N3, N5) 1.4 Wheel bearing kit replacement guide
    Deep interior cleaning | Car transformation by detailing
  • Replace Wheel hub bearing on Peugeot 306 7a - free video tips
    #DIY Wheel Rim Restoration: Revive Scratches and Chips Easily!