Important!

This replacement procedure can be used for:
SKODA Kushaq (PA1) TSI, SKODA Kushaq (PA1) 1.0 TSI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Top strut mount

Replacement: strut mount – SKODA Kushaq (PA1). Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      High-temperature ceramic grease
                    
                      Torque wrench
                    
                      HEX bit No.H6.
                    
                      Combination spanner #18
                    
                      Drive socket # 16 
                    
                      Drive socket # 18 
                    
                      Drive socket # 20.6 
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Hydraulic strut spring compressor
                    
                      Hammer
                    
                      Rubber mallet
                    
                      Hydraulic transmission jack
                    
                      Fender cover
                    
                      Wheel chock

Buy tools

Replacement: strut mount – SKODA Kushaq (PA1). Tip from AUTODOC experts:

The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
All mounts of the front shock struts should be replaced simultaneously.
All work should be done with the engine stopped.

Replacement: strut mount – SKODA Kushaq (PA1). Take the following steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. SKODA Kushaq (PA1)
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.

Step 7

Unscrew the fastener connecting the stabilizer link to the control arm. Use a drive socket #16. Use a ratchet wrench.
Step 8

Remove the fastening bolt.

Step 9

Remove the stabilizer rod.

Step 10

Clean the lower fastener connecting the suspension strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 11

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 12

Remove the fastening bolt.
Step 13

Disconnect the ABS sensor wiring.
Step 14

Disconnect the steering knuckle from the shock absorber strut. Use a rubber mallet.
Step 15

Lower the car.

Step 16

Open the bonnet.

Step 17

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 18

Clean the upper fastener of the suspension strut mount. Use a wire brush. Use WD-40 spray.
Step 19

Loosen the upper fastener of the shock strut mount. Use a drive socket #20.6. Use a ratchet wrench.

AUTODOC recommends:
SKODA Kushaq (PA1) – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
Step 20

Remove the suspension strut.
Step 21

Set the shock absorber strut on the spring compressor tool.

Replacement: strut mount – SKODA Kushaq (PA1). AUTODOC recommends:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 22

Compress the spring.
Step 23

Treat the shock strut rod. Use a wire brush. Use WD-40 spray.
Step 24

Remove the strut piston rod nut. Use a drive socket #20.6. Use a ratchet wrench.
Step 25

Remove the top strut mount.
Step 26

Install a new top shock strut mount.
Step 27

Tighten the shock strut piston rod nut. Use a drive socket #20.6. Use HEX No.H6. Use a torque wrench. Tighten it to 60 Nm torque.

Replacement: strut mount – SKODA Kushaq (PA1). Tip:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 28

Decompress the spring.

Step 29

Treat the shock strut rod. Use copper grease.

Step 30

Remove the assembled shock strut.
Step 31

Install the shock strut into the wheel arch.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. SKODA Kushaq (PA1)
Step 32

Tighten the upper fastener of the shock absorber strut mount. Use a drive socket #20.6. Use a torque wrench. Tighten it to 60 Nm torque.
Step 33

Treat the upper fastener of the suspension strut mount. Use copper grease.

Step 34

Remove the fender protection cover.

Step 35

Close the hood.

Step 36

Raise the front of the car and secure on supports.

Step 37

Treat the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 38

Fix the shock absorber strut on the steering knuckle.
Step 39

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 40

Install the fastening bolt. Use a hammer.

Step 41

Remove the support from under the steering knuckle.

AUTODOC recommends:
SKODA Kushaq (PA1) – Do not lower the transmission jack sharply to avoid damaging components and mechanisms of the car.
Step 42

Tighten the lower fasteners of the suspension strut. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. Tighten it to 60 Nm torque.+90°
Step 43

Ιnstall the transverse stabilizer link.

Step 44

Install the rod fastening to the stabilizer and tighten it. Use a drive socket #16. Use a torque wrench. Tighten it to 15 Nm torque.+90°
Step 45

Connect the ABS sensor wiring.
Step 46

Treat the surface where the brake disc contacts the wheel rim. Use high-temperature ceramic grease.
Step 47

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: strut mount – SKODA Kushaq (PA1). After applying the spray, wait a few minutes.
Step 48

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. SKODA Kushaq (PA1)
Step 49

Screw in the wheel bolts. Use wheel impact socket #17.
Step 50

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 51

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the SKODA Kushaq (PA1) model

SKODA Kushaq (PA1) tyre size

How to change rear brake discs on Skoda Octavia 1Z5 – replacement guide

Free download PDF
2.1 MB
How to change manual gearbox oil on Skoda Fabia 6Y5 – replacement guide

Free download PDF
2.29 MB
How to change rear wheel bearing on Skoda Octavia 1Z5 – replacement guide

Free download PDF
2.34 MB
How to change engine oil and filter on Skoda Octavia 1Z5 – replacement guide

Free download PDF
2.1 MB
How to change rear brake pads on Skoda Octavia 1Z5 – replacement guide

Free download PDF
1.59 MB
How to change rear light on Skoda Octavia 1Z5 – replacement guide

Free download PDF
2.09 MB

How to change strut mount on a car – replacement tutorial

Universal

Free download PDF
1.04 MB
How to change front strut mount on Skoda Octavia 1U – replacement guide

Free download PDF
3.45 MB
How to change rear strut mount on Skoda Fabia 6Y5 – replacement guide

Free download PDF
2.18 MB
How to change front strut mount on Skoda Fabia 6Y5 – replacement guide

Free download PDF
3.57 MB
How to change rear strut mount on SKODA CITIGO – replacement guide

Free download PDF
1.9 MB
How to change rear strut mount on SKODA OCTAVIA (1U2) – replacement guide

Free download PDF
1.9 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Coolant comparison test | AUTODOC

14K views

Published on: 18/02/2021
What to do if the ABS light comes on: DIY Diagnostics Tips

8K views

Published on: 11/03/2021
Revive Your Vehicle's Look | How to Restore Wheel Rims Yourself!

7K views

Published on: 13/05/2021
Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips

7K views

Published on: 30/03/2022