Replacement: strut mount – Skoda Fabia 6Y5. Tip from AUTODOC:
All mounts of the front shock struts should be replaced simultaneously.
The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
Be sure to replace all self-locking nuts and bolts during installation.
Warning! Shut down the engine before starting any work – Skoda Fabia 6Y5.
Carry out replacement in the following order:
Step 1
Open the bonnet.
Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3
Loosen the upper fastener of the shock strut mount. Use a drive socket #13. Use a ratchet wrench.
Step 4
Secure the wheels with chocks.
Step 5
Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 6
Remove the hub bearing protection cap.
Please note!
Some cars are not equipped with wheel hub caps.
Step 7
Unscrew the hub lock nut. Use drive 12-point socket #36.
Step 8
Raise the front of the car and secure on supports.
Step 9
Unscrew the wheel bolts.
Replacement: strut mount – Skoda Fabia 6Y5. AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 10
Remove the wheel.
Step 11.1
Clean the fasteners connecting the stabiliser link to the shock strut, and those connecting the shock strut to the steering knuckle.
Step 11.2
Use a wire brush. Use WD-40 spray.
Step 12
Unscrew the nut and remove the stabilizer rod from the shock strut. Use a combination spanner #16. Use HEX No.H5. Use a ratchet wrench.
Step 13
Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench.
Step 14
Detach the brake hose from the shock strut. Use a crowbar.
Step 15
Remove the fastening bolt.
Step 16
Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber. Use a ratchet wrench.
Step 17
Clean the ball joint mounting seat. Use a wire brush. Use WD-40 spray.
Step 18
Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #13. Use a ratchet wrench.
Step 19
Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 20
Disconnect the spherical joint from the arm. Use a crowbar.
Step 21
Unscrew the fastener connecting the drive shaft to the wheel hub. Use drive 12-point socket #36.
Step 22
Treat the mounting seat of the driveshaft on the steering knuckle. Use WD-40 spray.
Step 23
Pull the drive shaft out of the steering knuckle and lifting it, tie to the body. Use a pin punch. Use a hammer.
Replacement: strut mount – Skoda Fabia 6Y5. AUTODOC experts recommend:
Make sure that the drive shaft is not unloaded (when the car is jacked).
Step 24
Disconnect the steering knuckle from the shock absorber strut. Use a pin punch. Use a hammer.
Step 25
Lower the hydraulic transmission jack by 10-15 cm.
AUTODOC recommends:
Replacement: strut mount – Skoda Fabia 6Y5. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.Make sure that the steering knuckle is not released from load.
Step 26
Unscrew the top fastening of the shock strut mount. Use a drive socket #13. Use a ratchet wrench.
Replacement: strut mount – Skoda Fabia 6Y5. Tip from AUTODOC experts:
To avoid injuries, hold the shock strut when undoing the fastening bolts.
Step 27
Remove the suspension strut.
Step 28
Set the shock absorber strut on the spring compressor tool.
Replacement: strut mount – Skoda Fabia 6Y5. Professionals recommend:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 29
Compress the spring.
Step 30
Clean the shock absorber rod. Use a wire brush. Use WD-40 spray.
Step 31
Remove the strut piston rod nut. Use a combination spanner #21. Use HEX No.H7. Use a ratchet wrench.
Step 32
Remove the shock absorber mount, boot and bump stop.
Replacement: strut mount – Skoda Fabia 6Y5. Tip:
Examine the shock absorber dust cap and the bump stop. Replace them if necessary.
Step 33
Install the new mount, boot, and bump stop on the shock absorber.
Step 34
Tighten the shock strut piston rod nut. Use a combination spanner #21. Use HEX No.H7. Use a torque wrench. Tighten it to 60 Nm torque.
Replacement: strut mount – Skoda Fabia 6Y5. AUTODOC recommends:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 35
Decompress the spring.
Step 36
Remove the assembled shock strut.
Step 37
Install the shock strut into the wheel arch.
Step 38
Screw the top fastening of the shock strut mount. Do not tighten it.
AUTODOC recommends:
Important! Hold the suspension strut while screwing in the fastening bolts. Skoda Fabia 6Y5
Step 39
Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 40
Fix the shock absorber strut on the steering knuckle.
Step 41
Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 42
Clean the splines of the drive shaft CV joint. Use WD-40 spray.
Step 43
Install the drive shaft.
Step 44
Remove the support from under the steering knuckle.
AUTODOC recommends:
Skoda Fabia 6Y5 – Do not lower the transmission jack sharply to avoid damaging components and mechanisms of the car.
Step 45
Install and tighten a new bolt of the steering knuckle. Use a drive socket #18. Use a combination spanner #18. Use a torque wrench. Tighten it to 60 Nm torque.+90°
AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 46
Treat the shock strut fasteners. Use copper grease.
Step 47
Attach the ball joint to the control arm.
Step 48
Tighten the ball joint fastener. Use a drive socket #13. Use a torque wrench. Tighten it to 20 Nm torque.+90°
AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 49
Screw the nut of the drive shaft. Use drive 12-point socket #36.
Step 50
Secure the stabilizer link on the suspension strut. Use a combination spanner #16. Use HEX #H5. Use a torque wrench. Tighten it to 40 Nm torque.
Step 51
Fasten the brake hose on the strut.
Step 52
Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 53
Screw in the wheel bolts. Use wheel impact socket #17.
Replacement: strut mount – Skoda Fabia 6Y5. Tip from AUTODOC experts:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 54
Lower the car.
Step 55
Tighten the upper fastener of the shock absorber strut mount. Use a drive socket #13. Use a torque wrench. Tighten it to 15 Nm torque.+90°
AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 56
Screw the wheel hub lock nut. Use drive 12-point socket #36. Use a torque wrench. Tighten it to 50 Nm torque.+45°
AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 57
Tighten the wheel bolts using a criss-cross pattern. Use a torque wrench. Tighten it to 120 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the SKODA Fabia I Combi (6Y5) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your SKODA Fabia I Combi (6Y5)
View more
Top 5 reasons why the suspension knocks | AUTODOC tips
How to Make a DIY Foam Sprayer | AUTODOC tips
How to Order Car Parts Online: Avoid These 5 Common Pitfalls
Transform Your Old Engine Valve Cover: Quick Polishing Tips for a Shiny Finish | AUTODOC Tips