Important!

This replacement procedure can be used for:
SKODA Citigo Hatchback 1.0 CNG, SKODA Citigo Hatchback 1.0, SKODA Citigo Hatchback 1.0 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Repair kit, suspension strut

Replacement: strut mount – SKODA CITIGO. Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Drive socket # 16 
                    
                      Combination spanner #16
                    
                      Torque wrench
                    
                      Adjustable wrench
                    
                      Wheel impact socket #17
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: strut mount – SKODA CITIGO. AUTODOC recommends:

All work should be done with the engine stopped.
The replacement procedure is identical for the mounts of the right and left shock absorbers of the rear suspension.
Both mounts of the rear shock struts should be replaced simultaneously.
Be sure to replace all self-locking nuts and bolts during installation.

Replacement: strut mount – SKODA CITIGO. Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: strut mount – SKODA CITIGO. Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Support the arm. Use a hydraulic transmission jack.
Step 8

Unscrew the lower fastener of the shock absorber. Use a combination spanner #16. Use a drive socket #16.
Step 9

Unscrew the upper fastener of the shock absorber. Use a drive socket #16.

AUTODOC recommends:
Important! Hold the shock absorber while unscrewing the fastening bolts. SKODA CITIGO
Step 10

Remove the support from under the rear arm.
Step 11

Remove the shock absorber.
Step 12

Remove the protective cap of the shock absorber mount.
Step 13

Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray.
Step 14

Remove the shock absorber piston rod fastening. Use a combination spanner #16. Use an adjustable wrench.
Step 15

Remove the shock absorber mount, boot and bump stop.

AUTODOC recommends:
Τhoroughly examine the shock absorber mount, dust boot, bump stop. Replace them if necessary.
Step 16

Install the boot and a bump stop onto the shock absorber.
Step 17

Install the new shock absorber mount.
Step 18

Tighten the shock absorber mount fasteners. Use a combination spanner #16. Use an adjustable wrench. Use a torque wrench. Tighten it to 25 Nm torque.
Step 19

Place the shock absorber in the wheel arch and secure it.
Step 20

Install the shock absorber mount using the center hole as a guide.
Step 21

Tighten the top shock absorber fastening. Important! Be sure to use new fasteners. Use a drive socket #16. Use a torque wrench. Tighten it to 30 Nm torque.+90°
Step 22

Support the arm. Use a hydraulic transmission jack.
Step 23

Tighten the lower fastener of the shock absorber. Important! Be sure to use new fasteners. Use a combination spanner #16. Use a drive socket #16. Use a torque wrench. Tighten it to 40 Nm torque.+90°
Step 24

Remove the support from under the rear arm.
Step 25

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 26

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. SKODA CITIGO
Step 27

Screw in the wheel bolts. Use wheel impact socket #17.
Step 28

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 120 Nm torque.
Step 29

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the SKODA Citigo Hatchback model

SKODA CITIGO tyre size

How to change front strut mount on SKODA Citigo – replacement guide

Free download PDF
3.03 MB
How to change track rod end on SKODA CITIGO – replacement guide

Free download PDF
1.45 MB
How to change front anti roll bar links on SKODA CITIGO – replacement guide

Free download PDF
1.32 MB
How to change front brake pads on SKODA CITIGO – replacement guide

Free download PDF
1.37 MB
How to change serpentine belt on SKODA CITIGO – replacement guide

Free download PDF
675.84 KB
How to change front windshield wipers on SKODA CITIGO – replacement guide

Free download PDF
512 KB

How to change front strut mount on SKODA Citigo – replacement guide

Free download PDF
3.03 MB
How to change front strut mount on SKODA Citigo-e iV (NE1) – replacement guide

Free download PDF
3.05 MB
How to change strut mount on a car – replacement tutorial

Universal

Free download PDF
1.04 MB
How to change front strut mount on Skoda Octavia 1U – replacement guide

Free download PDF
3.45 MB
How to change rear strut mount on Skoda Fabia 6Y5 – replacement guide

Free download PDF
2.18 MB
How to change front strut mount on Skoda Fabia 6Y5 – replacement guide

Free download PDF
3.57 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Transform Your Car's Look: 6 Simple Accessories You Need to Try!

3K views

Published on: 18/11/2021
How to fix your car with AUTODOC CLUB

17K views

Published on: 30/11/2021
Top 4 Car Cleaning Products to Protect Your Car's Body | AUTODOC Tips

2K views

Published on: 26/08/2021
Why does it burn oil? The main cause of oil consumption in EA888 Gen 1

118K views

Published on: 14/08/2025