Disclaimer
How to change front strut mount on Renault Kangoo KC01 – replacement guide
downloads:
10
Views:
143
Important!
This replacement procedure can be used for:
RENAULT KANGOO (KC0/1_) 1.2 (KC0A, KC0K, KC0F, KC01), RENAULT KANGOO (KC0/1_) 1.4 (KC0C, KC0H, KC0B, KC0M), RENAULT KANGOO (KC0/1_) D 1.9, RENAULT KANGOO (KC0/1_) D 1.9, RENAULT KANGOO (KC0/1_) 1.9 dTi (KC0U), RENAULT KANGOO (KC0/1_) 1.6 16V 4x4 (KC0P, KC0S, KC0L), RENAULT KANGOO (KC0/1_) 1.5 dCi (KC07), RENAULT KANGOO (KC0/1_) 1.9 dCi 4x4 (KC0V), RENAULT KANGOO (KC0/1_) 1.5 dCi (KC08, KC09), RENAULT KANGOO (KC0/1_) 1.5 dCi, RENAULT KANGOO (KC0/1_) 1.6 16V bivalent, RENAULT KANGOO (KC0/1_) 1.5 dCi, RENAULT KANGOO (KC0/1_) 1.5 dCi, RENAULT KANGOO (KC0/1_) 1.6 (KC00) … View more
The steps may slightly vary depending on the car design.
RENAULT KANGOO (KC0/1_) 1.2 (KC0A, KC0K, KC0F, KC01), RENAULT KANGOO (KC0/1_) 1.4 (KC0C, KC0H, KC0B, KC0M), RENAULT KANGOO (KC0/1_) D 1.9, RENAULT KANGOO (KC0/1_) D 1.9, RENAULT KANGOO (KC0/1_) 1.9 dTi (KC0U), RENAULT KANGOO (KC0/1_) 1.6 16V 4x4 (KC0P, KC0S, KC0L), RENAULT KANGOO (KC0/1_) 1.5 dCi (KC07), RENAULT KANGOO (KC0/1_) 1.9 dCi 4x4 (KC0V), RENAULT KANGOO (KC0/1_) 1.5 dCi (KC08, KC09), RENAULT KANGOO (KC0/1_) 1.5 dCi, RENAULT KANGOO (KC0/1_) 1.6 16V bivalent, RENAULT KANGOO (KC0/1_) 1.5 dCi, RENAULT KANGOO (KC0/1_) 1.5 dCi, RENAULT KANGOO (KC0/1_) 1.6 (KC00) … View more
The steps may slightly vary depending on the car design.
How to change front strut mount / top munt RENAULT KANGOO 1 (KC) [TUTORIAL AUTODOC]

All the parts you need to replace – Strut Mount for KANGOO (KC0/1_) and other RENAULT models
Alternative products

Wire brush
WD-40 spray
Copper grease
Combination spanner #14
Combination spanner #19
Combination spanner #21
Drive socket # 21
HEX bit No.H6.
Wheel impact socket #19
Pin punch
Hammer
Tap wrench
Ratchet wrench
Torque wrench
Crow bar
Hydraulic transmission jack
Hydraulic strut spring compressor
Fender cover
Wheel chock
Replacement: strut mount – Renault Kangoo KC01. AUTODOC recommends:
- All mounts of the front shock struts should be replaced simultaneously.
- The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
- Be sure to replace all self-locking nuts and bolts during installation.
- All work should be done with the engine stopped.
Replacement: strut mount – Renault Kangoo KC01. Recommended sequence of steps:
- Step 1
Open the bonnet. - Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Remove the shock strut mount cap. Use a crowbar. - Step 4
Loosen the upper fastener of the shock strut mount. Use a combination spanner #21. Use HEX No.H6. Use a ratchet wrench. - Step 5
Secure the wheels with chocks. - Step 6
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 7
Raise the front of the car and secure on supports. - Step 8
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. Renault Kangoo KC01 - Step 9
Remove the wheel. - Step 10
Clean the shock strut fasteners. Use a wire brush. Use WD-40 spray. - Step 11
Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #21. Use a combination spanner #21. Use a tap wrench. - Step 12
Prop up the steering knuckle. Use a hydraulic transmission jack. - Step 13
Remove the fastening bolts (2 pieces). Use a hammer. Use a pin punch. - Step 14
Unscrew the upper fastening of the shock absorber strut. Use a drive socket #21.Replacement: strut mount – Renault Kangoo KC01. Tip:To avoid injuries, hold the shock strut when undoing the fastening bolts. - Step 15
Remove the suspension strut. - Step 16
Set the shock absorber strut on the spring compressor tool.Replacement: strut mount – Renault Kangoo KC01. Tip from AUTODOC experts:Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles. - Step 17
Compress the spring. - Step 18
Remove the strut piston rod nut. Use HEX No.H6. Use a combination spanner #14. Use a ratchet wrench. - Step 19
Remove the top strut mount. - Step 20
Install a new top shock strut mount. - Step 21
Tighten the shock strut piston rod nut. Use HEX No.H6. Use a combination spanner #14. Use a torque wrench. Tighten it to 60 Nm torque.Replacement: strut mount – Renault Kangoo KC01. AUTODOC experts recommend:Check to make sure the spring is positioned correctly. Avoid its misalignment. - Step 22
Decompress the spring.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Kangoo I (KC) model
Popular maintenance tutorials for Renault Kangoo kc01
Complete guides for changing the Strut mount on different RENAULT KANGOO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT KANGOO (KC0/1_)
View more
Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide
DIY brake caliper restoration | AUTODOC tips
Coolant comparison test | AUTODOC
5 signs of a faulty strut mount and how to fix it
Most commonly replaced car parts on RENAULT KANGOO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME

































