Disclaimer
How to change front strut mount on OPEL Corsa С Van (X01) – replacement guide
downloads:
4
Views:
33
Important!
This replacement procedure can be used for:
OPEL Corsa C Van (X01) 1.2 16V (F08, W5L), OPEL Corsa C Van (X01) 1.7 DI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.7 DTI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.3 CDTI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.2 (F08, W5L), OPEL Corsa C Van (X01) 1.7 CDTi (F08, W5L) … View more
The steps may slightly vary depending on the car design.
OPEL Corsa C Van (X01) 1.2 16V (F08, W5L), OPEL Corsa C Van (X01) 1.7 DI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.7 DTI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.3 CDTI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.2 (F08, W5L), OPEL Corsa C Van (X01) 1.7 CDTi (F08, W5L) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Strut Mount for Corsa C Van (X01) and other OPEL models
Alternative products

Wire brush
WD-40 spray
Copper grease
Drive socket # 9
Drive socket # 17
Drive socket # 18
Combination spanner #17
Combination spanner #18
Combination spanner #19
Wheel impact socket #17
Ratchet wrench
Torque wrench
Flat screwdriver
Tap wrench
Crow bar
Hydraulic transmission jack
Hydraulic strut spring compressor
Fender cover
Wheel chock
Replacement: strut mount – OPEL CORSA C Box (F08, W5L). Professionals recommend:
- All mounts of the front shock struts should be replaced simultaneously.
- The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
- Be sure to replace all self-locking nuts and bolts during installation.
- All work should be done with the engine stopped.
Replacement: strut mount – OPEL CORSA C Box (F08, W5L). Take the following steps:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Remove the shock strut mount cap. Use a flat screwdriver.Step 4Treat the shock strut rod. Use a wire brush. Use WD-40 spray.Step 5
Unscrew the shock absorber mount fastening. Use a combination spanner #17. Use a drive socket #9. Use a ratchet wrench. - Step 6
Secure the wheels with chocks. - Step 7
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 8Raise the front of the car and secure on supports.Step 9
Unscrew the wheel bolts.Replacement: strut mount – OPEL CORSA C Box (F08, W5L). AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 10
Remove the wheel. - Step 11
Clean the fasteners connecting the stabiliser link to the shock strut, and those connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray. - Step 12
Unscrew the nut and remove the stabilizer rod from the shock strut. Use a combination spanner #19. Use a drive socket #18. Use a ratchet wrench. - Step 13
Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench. - Step 14
Prop up the steering knuckle. Use a hydraulic transmission jack. - Step 15
Remove the fastener attaching the brake hose to the shock strut. - Step 16
Disconnect the brake hose holder from the shock absorber strut. Use a flat screwdriver. - Step 17
Disconnect the steering knuckle from the shock absorber strut. Use a crowbar. - Step 18
Unscrew the upper fastening of the shock absorber strut. Use a combination spanner #17. Use a drive socket #9.AUTODOC recommends:Important! Hold the suspension strut while unscrewing the fastening bolts. OPEL CORSA C Box (F08, W5L) - Step 19
Remove the suspension strut. - Step 20
Set the shock absorber strut on the spring compressor tool.Replacement: strut mount – OPEL CORSA C Box (F08, W5L). AUTODOC experts recommend:Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles. - Step 21
Compress the spring. - Step 22
Remove the strut piston rod nut. Use a combination spanner #19. Use a drive socket #9. - Step 23
Remove the shock absorber mount, boot and bump stop. Use a crowbar. - Step 24
Install the new mount, boot, and bump stop on the shock absorber. - Step 25
Tighten the shock strut piston rod nut. Use a combination spanner #19. Use a drive socket #9. Use a torque wrench. Tighten it to 50 Nm torque.Replacement: strut mount – OPEL CORSA C Box (F08, W5L). Tip:Check to make sure the spring is positioned correctly. Avoid its misalignment. Important! Be sure to use new fasteners. - Step 26
Decompress the spring. - Step 27
Remove the assembled shock strut.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the OPEL Corsa C Van (X01) model
Popular maintenance tutorials for Opel Corsa C Van
Complete guides for changing the Strut mount on different OPEL CORSA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your OPEL Corsa C Van (X01)
View more
How to remove scratches from car plastic | AUTODOC tips
How to prevent car windows from fogging up | AUTODOC tips
DIY jack restoration | AUTODOC tips
Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips
Most commonly replaced car parts on OPEL CORSA
ОЕ number
Time to replace parts? Get even better deals in our Shop app.

SCAN ME






























