Important!

This replacement procedure can be used for:
OPEL Corsa C Van (X01) 1.4 (W5L, F08), OPEL Corsa C Van (X01) 1.2 (F08, W5L), OPEL Corsa C Van (X01) 1.3 CDTI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.7 DTI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.7 DI 16V (F08, W5L), OPEL Corsa C Van (X01) 1.2 16V (F08, W5L) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for Corsa C Van (X01) and other OPEL models

Wheel bearing kit

        Wheel bearing kit for Corsa C Van (X01) Petrol (75 hp)
      
        Wheel bearing kit for Corsa C Van (X01) Diesel (65 hp)
      
        Wheel bearing kit for Corsa C Van (X01) Diesel (75 hp)
      
        Wheel bearing kit for Corsa C Van (X01) Diesel (69 hp)
      
        Wheel bearing kit for Corsa C Van (X01) Petrol (80 hp)
      
        Wheel bearing kit for Corsa C Van (X01) Petrol (90 hp)

Replacement: wheel bearing – OPEL CORSA C Box (F08, W5L). Tools you might need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        All-purpose cleaning spray
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Combination spanner #16
                      
                        Combination spanner #18
                      
                        Drive socket # 16 
                      
                        Drive socket # 17
                      
                        Drive socket # 18 
                      
                        Drive socket # E20 
                      
                        Drive socket # 30 
                      
                        Torx bit T30
                      
                        Bush and bearing driver set
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Tap wrench
                      
                        Hammer
                      
                        Pin punch
                      
                        Crow bar
                      
                        Ball joint puller
                      
                        Circlip pliers
                      
                        Wheel chock

Buy tools

Replacement: wheel bearing – OPEL CORSA C Box (F08, W5L). AUTODOC recommends:

Do not re-use the bearing assembly of your OPEL CORSA C Box (F08, W5L) car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
Please note: all work on the car – OPEL CORSA C Box (F08, W5L) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Remove the cotter pin. Use a crowbar.
Step 3

Loosen the fastener of the driveshaft. Use a drive socket #30. Use a tap wrench.
Step 4

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 5

Raise the front of the car and secure on supports.

Step 6

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. OPEL CORSA C Box (F08, W5L)
Step 7

Remove the wheel.
Step 8

Treat the ABS sensor connector. Use all-purpose cleaning spray.
Step 9

Detach the ABS sensor connector.
Step 10

Disconnect the ABS sensor wiring.
Step 11

Spread the brake pads. Use a crowbar.
Step 12

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 13

Unscrew the caliper bracket fastening. Use a drive socket #Е20. Use a ratchet wrench. Use a tap wrench.
Step 14

Remove the brake caliper together with its bracket.

Replacement: wheel bearing – OPEL CORSA C Box (F08, W5L). AUTODOC experts recommend:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 15

Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 16

Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
Step 17

Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
Step 18

Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
Step 19

Unscrew the brake disc fastening. Use Torx T30. Use a ratchet wrench.
Step 20

Remove the brake disc.
Step 21

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 22

Unscrew the fasteners connecting the suspension strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench.
Step 23

Remove the fastening bolt.
Step 24

Unscrew the fastener connecting the ball joint to the steering knuckle. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 25

Remove the fastening bolt.
Step 26

Disconnect the lower arm from the steering knuckle.
Step 27

Unscrew the fastener connecting the drive shaft to the wheel hub.
Step 28

Detach the driveshaft from the steering knuckle.
Step 29

Remove the fastening bolt.
Step 30

Remove the steering knuckle together with the hub.

Step 31

Clean the fasteners of the brake disc cover. Use a wire brush. Use WD-40 spray.
Step 32

Unscrew the fasteners of the brake disc cover. Use Torx T30.
Step 33

Remove the brake disc cover.
Step 34

Remove the wheel hub from the steering knuckle. Use a bush and bearing driver set.
Step 35

Clean the fasteners of the wheel hub bearing. Use a wire brush. Use WD-40 spray.
Step 36

Remove the wheel hub bearing retaining ring. Use a pin punch. Use a hammer. Use a crowbar.
Step 37

Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
Step 38

Press out the wheel hub bearing. Use a bush and bearing driver set.
Step 39

Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
Step 40

Press the new bearing in the steering knuckle. Use a bush and bearing driver set.

Replacement: wheel bearing – OPEL CORSA C Box (F08, W5L). Tip from AUTODOC experts:
Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
Step 41

Install the wheel hub bearing retaining ring. Use circlip pliers.
Step 42

Clean the hub. Use WD-40 spray.
Step 43

Pull the bearing inner race out of the wheel hub. Use a bearing separator. Use a bush and bearing driver set.

Step 44

Clean the hub. Use WD-40 spray.

Step 45

Install the wheel hub on the steering knuckle. Use a bush and bearing driver set.

Replacement: wheel bearing – OPEL CORSA C Box (F08, W5L). AUTODOC recommends:
Make sure that the wheel hub is positioned correctly. Avoid any misalignment.
Step 46

Clean the splines of the drive shaft CV joint. Use a wire brush. Use WD-40 spray.
Step 47

Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 48

Install the steering knuckle assembled with the wheel hub.
Step 49

Install the fastening bolt.

Step 50

Install the drive shaft.
Step 51

Connect the lower arm to the steering knuckle.
Step 52

Install the fastening bolt.
Step 53

Screw the fasteners of the ball joint. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 54

Tighten the ball joint fastener. Use a combination spanner #16. Use a drive socket #16. Use a torque wrench. Tighten it to 55 Nm torque.
Step 55

Install the fastening bolt.
Step 56

Screw in the fasteners connecting the suspension strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 57

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. Tighten it to 80 Nm torque.+60°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 58

Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
Step 59

Connect the tie rod end to the steering knuckle.
Step 60

Tighten the fastening nut connecting the tie rod end to the steering knuckle. Use a drive socket #17. Use a torque wrench. Tighten it to 35 nm torque.
Step 61

Install the brake disc cover.
Step 62

Screw in the fasteners of the brake disc cover. Use Torx T30.
Step 63

Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 64

Install the brake disc.
Step 65

Tighten the brake disc fastening. Use Torx T30. Use a torque wrench. Tighten it to 8 Nm torque.
Step 66

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – OPEL CORSA C Box (F08, W5L). After applying the spray, wait a few minutes.
Step 67

Install the brake caliper together with its bracket.
Step 68

Tighten the brake caliper bracket. Use a drive socket #Е20. Use a torque wrench. Tighten it to 100 Nm torque.
Step 69

Attach the ABS sensor connector.
Step 70

Connect the ABS sensor wiring.
Step 71

Screw the nut of the drive shaft. Use a drive socket #30. Use a ratchet wrench.
Step 72

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 73

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – OPEL CORSA C Box (F08, W5L). After applying the spray, wait a few minutes.
Step 74

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. OPEL CORSA C Box (F08, W5L)
Step 75

Screw in the wheel bolts. Use wheel impact socket #17.
Step 76

Lower the car.
Step 77

Tighten the drive shaft nut. Use a drive socket #30. Use a torque wrench. Tighten it to 177 Nm torque.
Step 78

Install the cotter pin. Use a crowbar.
Step 79

Treat the CV axle fastener. Use copper grease.
Step 80

Tighten the wheel bolts using a criss-cross pattern. Use a torque wrench. Tighten it to 110 Nm torque.
Step 81

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the OPEL Corsa C Van (X01) model.

Browse tyres

How to change front strut mount on OPEL Corsa С Van (X01) – replacement guide

Free download PDF
3.12 MB
How to change front lower arm on OPEL Corsa C Van (X01) – replacement guide

Free download PDF
2.09 MB
How to change track rod end on OPEL Corsa C Van (X01) – replacement guide

Free download PDF
1.3 MB
How to change front anti roll bar links on OPEL Corsa С Van (X01) – replacement guide

Free download PDF
1.2 MB
How to change rear wheel bearing on OPEL Corsa С Van (X01) – replacement guide

Free download PDF
1.62 MB
How to change front brake pads on OPEL Corsa С Van (X01) – replacement guide

Free download PDF
1.51 MB

How to change rear wheel bearing on Opel Corsa D – replacement guide

Free download PDF
1.63 MB
How to change front wheel bearing on Opel Corsa D – replacement guide

Free download PDF
4.18 MB
How to change front wheel bearing on OPEL Corsa E Hatchback (X15) – replacement guide

Free download PDF
4.28 MB
How to change front wheel bearing on Opel Corsa C – replacement guide

Free download PDF
2.95 MB
How to change rear wheel bearing on OPEL Corsa C Hatchback (X01) – replacement guide

Free download PDF
1.57 MB
How to change rear wheel bearing on Opel Corsa S93 – replacement guide

Free download PDF
2.11 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Top 5 mistakes when replacing spark plugs | AUTODOC tips

9K views

Published on: 13/07/2023
5 car tips for a winter's day | AUTODOC tips

5K views

Published on: 05/02/2024
TOP 5 mistakes when replacing shock absorbers | AUTODOC tips

8K views

Published on: 15/06/2023
How to replace the suspension on a BMW E30 Turbo | SUPERCAR AUTODOC

1K views

Published on: 04/03/2021