
Disclaimer
How to change front lower arm on VW Bora Saloon (1J2) – replacement guide
downloads:
3
Views:
23
Important!
This replacement procedure can be used for:
VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.0, VW Bora Saloon (1J2) 2.3 V5, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.8, VW Bora Saloon (1J2) 1.4 16V, VW Bora Saloon (1J2) 1.9 SDI, VW Bora Saloon (1J2) 2.8 V6 4motion, VW Bora Saloon (1J2) 1.8 4motion, VW Bora Saloon (1J2) 2.3 V5 4motion, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.6 16V, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.3 V5, VW Bora Saloon (1J2) 2.3 V5 4motion, VW Bora Saloon (1J2) 1.8 T, VW Bora Saloon (1J2) 2.0 4motion, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.6 FSI, VW Bora Saloon (1J2) 1.8 T, VW Bora Saloon (1J2) 1.6 … View more
The steps may slightly vary depending on the car design.
VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.0, VW Bora Saloon (1J2) 2.3 V5, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.8, VW Bora Saloon (1J2) 1.4 16V, VW Bora Saloon (1J2) 1.9 SDI, VW Bora Saloon (1J2) 2.8 V6 4motion, VW Bora Saloon (1J2) 1.8 4motion, VW Bora Saloon (1J2) 2.3 V5 4motion, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.6 16V, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.3 V5, VW Bora Saloon (1J2) 2.3 V5 4motion, VW Bora Saloon (1J2) 1.8 T, VW Bora Saloon (1J2) 2.0 4motion, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI 4motion, VW Bora Saloon (1J2) 1.6 FSI, VW Bora Saloon (1J2) 1.8 T, VW Bora Saloon (1J2) 1.6 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Control Arm for Bora Saloon (1J2) and other VW models
Suspension arm
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #18
Drive socket # 13
Drive socket # 16
Drive socket # 18
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: front lower arm – VW BORA (1J2). Tip from AUTODOC:
- The replacement procedure is identical for the left and right lower control arms.
- All work should be done with the engine stopped.
Replacement: front lower arm – VW BORA (1J2). Recommended sequence of steps:
- Step 1Secure the wheels with chocks.Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the front of the car and secure on supports.Step 4Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW BORA (1J2)
- Step 5Remove the wheel.
- Step 6Clean all joints of the arm. Use a wire brush. Use WD-40 spray.AUTODOC recommends:Replacement: front lower arm – VW BORA (1J2). After applying the spray, wait a few minutes.Wear protective goggles.
- Step 7Unscrew the fastener connecting the stabilizer bar with the control arm. Use a drive socket #16. Use a tap wrench.
- Step 8Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #13. Use a tap wrench.
- Step 9Loosen the front fastener of the control arm. Use a drive socket #18. Use a tap wrench.
- Step 10Unscrew the rear arm fastener. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench.
- Step 11Remove the rear fastener of the control arm.
- Step 12Unscrew the front arm fastener. Use a drive socket #18. Use a ratchet wrench.
- Step 13Remove the front fastener of the control arm.
- Step 14Disconnect the spherical joint from the arm.
- Step 15Remove the arm. Use a crowbar.
- Step 16Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
- Step 17Install a new arm.Replacement: front lower arm – VW BORA (1J2). AUTODOC experts recommend:During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
- Step 18Install the control arm fasteners.
- Step 19Attach the ball joint to the control arm.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Bora Saloon (1J2) model
Popular maintenance tutorials for VW Bora 1j2
Complete guides for changing the Control arm on different VW BORA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Bora Saloon (1J2)
View more
- How to unlock your car without a key | AUTODOC tips
- #DIY guide: Changing your car's color with a spray can | AUTODOC tips
- 5 tools that make car repair incredibly simple | AUTODOC tips
- DIY vehicle AC compressor restoration
Most commonly replaced car parts on VW BORA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME