Important!

This replacement procedure can be used for:
VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.0, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.8, VW Bora Saloon (1J2) 1.4 16V, VW Bora Saloon (1J2) 1.9 SDI, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.6 16V, VW Bora Saloon (1J2) 1.9 TDI, VW Bora Saloon (1J2) 1.6, VW Bora Saloon (1J2) 2.3 V5, VW Bora Saloon (1J2) 1.8 T, VW Bora Saloon (1J2) 1.9 TDI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Top strut mount

Replacement: strut mount – VW BORA (1J2). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #16
                    
                      Drive socket # 16 
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Shock absorber socket #DD6
                    
                      Vice
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: strut mount – VW BORA (1J2). Tip from AUTODOC experts:

The replacement procedure is identical for the mounts of the right and left shock absorbers of the rear suspension.
Both mounts of the rear shock struts should be replaced simultaneously.
Be sure to replace all self-locking nuts and bolts during installation.
Please note: all work on the car – VW BORA (1J2) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. VW BORA (1J2)
Step 5

Remove the wheel.
Step 6

Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Support the rear suspension beam. Use a hydraulic transmission jack.
Step 8

Unscrew the lower fastener of the shock absorber. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 9

Unscrew the upper fastener of the shock absorber. Use a drive socket #16. Use a ratchet wrench.
Step 10

Remove the fastening bolt.
Step 11

Remove the mounting from under the rear axle beam.

Replacement: strut mount – VW BORA (1J2). Professionals recommend:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 12

Remove the shock absorber.
Step 13

Remove the protective cap of the shock absorber mount.
Step 14

Grip the shock absorber in a vice.
Step 15

Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray.
Step 16

Remove the shock absorber piston rod fastening. Use a drive socket #16. Use a shock absorber socket DD№6. Use a ratchet wrench.
Step 17

Remove the shock absorber mount, boot and bump stop.

Replacement: strut mount – VW BORA (1J2). Tip from AUTODOC:
Examine the shock absorber dust cap and the bump stop. Replace them if necessary.
Step 18

Install the new mount, boot, and bump stop on the shock absorber.
Step 19

Tighten the shock absorber rod nut. Use a drive socket #16. Use a shock absorber socket DD№6. Use a torque wrench. Tighten it to 25 nm torque.
Step 20

Treat the shock absorber rod fastener. Use copper grease.
Step 21

Release the vice and take out the shock absorber.
Step 22

Install the protective cap of the shock absorber mount.
Step 23

Clean the shock absorber mounting seats. Use a wire brush. Use WD-40 spray.
Step 24

Treat the shock absorber mounting seats. Use copper grease.

Step 25

Place the shock absorber in the wheel arch and secure it.

AUTODOC recommends:
VW BORA (1J2) – To avoid injury, hold the shock absorber while screwing in the fastening bolts.
Step 26

Screw the upper fastener of the shock absorber. Use a drive socket #16. Use a ratchet wrench.

Replacement: strut mount – VW BORA (1J2). AUTODOC experts recommend:
Install the shock absorber mount using the center hole as a guide.
Step 27

Tighten the top shock absorber fastening. Use a drive socket #16. Use a torque wrench. Tighten it to 30 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 28

Install the fastening bolt.
Step 29

Screw in the lower fastener of the shock absorber. Use a drive socket #16. Use a ratchet wrench.
Step 30

Support the rear suspension beam. Use a hydraulic transmission jack.
Step 31

Tighten the lower fastener of the shock absorber. Use a combination spanner #16. Use a drive socket #16. Use a torque wrench. Tighten it to 40 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 32

Remove the mounting from under the rear axle beam.

AUTODOC recommends:
VW BORA (1J2) – Do not lower the transmission jack sharply to avoid damaging components and mechanisms of the car.
Step 33

Treat the shock absorber fasteners. Use copper grease.
Step 34

Clean the wheel rim mounting seat. Use a wire brush.
Step 35

Treat the surface where the wheel rim contacts the brake drum. Use copper grease.
Step 36

Install the wheel.

Replacement: strut mount – VW BORA (1J2). Tip from AUTODOC:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 37

Screw in the wheel bolts. Use wheel impact socket #17.
Step 38

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 39

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the VW Bora Saloon (1J2) model

VW Bora 1j2 tyre size

How to change front strut mount on VW Bora Saloon (1J2) – replacement guide

Free download PDF
2.8 MB
How to change front lower arm on VW Bora Saloon (1J2) – replacement guide

Free download PDF
2.05 MB
How to change front ball joint on VW Bora Saloon (1J2) – replacement guide

Free download PDF
1.4 MB
How to change track rod end on VW Bora Saloon (1J2) – replacement guide

Free download PDF
1.62 MB
How to change front anti roll bar links on VW Bora Saloon (1J2) – replacement guide

Free download PDF
1.3 MB
How to change front wheel bearing on VW Bora Saloon (1J2) – replacement guide

Free download PDF
4.03 MB

How to change front strut mount on VW Bora Saloon (1J2) – replacement guide

Free download PDF
2.8 MB
How to change rear strut mount on VW Bora Variant (1J6) – replacement guide

Free download PDF
1.96 MB
How to change front strut mount on VW Bora Variant (1J6) – replacement guide

Free download PDF
2.8 MB
How to change front strut mount on VW BORA – replacement guide

Free download PDF
1.75 MB
How to change strut mount on a car – replacement tutorial

Universal

Free download PDF
1.04 MB
How to change front strut mount on VW Polo 9N – replacement guide

Free download PDF
2.08 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

5 Essential Tips to Prepare Your Car for Winter | AUTODOC tips

6K views

Published on: 05/02/2024
Save Money on Fuel with These Easy Tips | AUTODOC

5K views

Published on: 27/09/2022
Top 7 signs of a bad starter

5K views

Published on: 20/03/2025
Transform Your Old Engine Valve Cover: Quick Polishing Tips for a Shiny Finish | AUTODOC Tips

11K views

Published on: 30/11/2023