Disclaimer
How to change front lower arm on SEAT Exeo ST (3R5) – replacement guide
downloads:
8
Views:
69
Important!
This replacement procedure can be used for:
SEAT Exeo ST (3R5) 1.6, SEAT Exeo ST (3R5) 1.8 T, SEAT Exeo ST (3R5) 2.0 TFSI, SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TDI … View more
The steps may slightly vary depending on the car design.
SEAT Exeo ST (3R5) 1.6, SEAT Exeo ST (3R5) 1.8 T, SEAT Exeo ST (3R5) 2.0 TFSI, SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TDI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Control Arm for Exeo ST (3R5) and other SEAT models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #18
Drive socket # 18
Wheel impact socket #17
Ball joint puller
Hydraulic transmission jack
Wheel chock
Replacement: front lower arm – SEAT EXEO ST (3R5). Professionals recommend:
- The replacement procedure is identical for the left and right lower control arms.
- Please note: all work on the car – SEAT EXEO ST (3R5) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: front lower arm – SEAT EXEO ST (3R5). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean all joints of the arm. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #18. - Step 8
Unscrew the rear fastener connecting the control arm to the subframe. Use a combination spanner #18 (2 pieces). - Step 9
Disconnect the ball joint from the steering knuckle. Use a ball joint puller. - Step 10
Remove the fastening bolt. - Step 11
Remove the arm. - Step 12
Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray. - Step 13
Install a new arm. - Step 14
Connect the ball joint to the steering knuckle. - Step 15Install the fastening bolt.Step 16
Screw the fasteners of the ball joint. Use a combination spanner #18. - Step 17
Screw the rear arm fastener. Use a combination spanner #18 (2 pieces).
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Exeo ST (3R5) model
Popular maintenance tutorials for Seat Exeo st
Complete guides for changing the Control arm on different SEAT EXEO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Exeo ST (3R5)
View more
5 Ways You’re Scrubbing Your Car Wrong | AUTODOC Tips
Top 5 brake repair mistakes | AUTODOC tips
Which Coolant is Best? Comparison Test | AUTODOC
Deep interior cleaning | Car transformation by detailing
Most commonly replaced car parts on SEAT EXEO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME































