Disclaimer
How to change rear anti roll bar links on SEAT Exeo ST (3R5) – replacement guide
downloads:
0
Views:
2
Important!
This replacement procedure can be used for:
SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TFSI, SEAT Exeo ST (3R5) 1.8 T, SEAT Exeo ST (3R5) 1.6 … View more
The steps may slightly vary depending on the car design.
SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TDI, SEAT Exeo ST (3R5) 2.0 TFSI, SEAT Exeo ST (3R5) 1.8 T, SEAT Exeo ST (3R5) 1.6 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for Exeo ST (3R5) and other SEAT models
Anti-roll bar link
Anti-roll bar link
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #16
Combination spanner #18
Drive socket # 13
Wheel impact socket #17
Ratchet wrench
Torque wrench
Hydraulic transmission jack
Wheel chock
AUTODOC recommends:
- Replace stabilizer links on SEAT EXEO ST (3R5) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – SEAT EXEO ST (3R5) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. SEAT EXEO ST (3R5) - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use a combination spanner #18. - Step 8
Unscrew the fastener connecting the stabilizer bar with the control arm. Use a drive socket #13. Use a ratchet wrench. - Step 9
Remove the stabilizer rod.Replacement: anti roll bar links – SEAT EXEO ST (3R5). Tip:Examine stabiliser bushes. Replace them if needed. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Install a new rod, tighten the fasteners. - Step 12
Tighten the fastener connecting the stabilizer bar with the control arm. Use a drive socket #13. Use a torque wrench. Tighten it to 25 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Exeo ST (3R5) model.
Popular maintenance tutorials for Seat Exeo st
Free download PDF
2.13 MB
Free download PDF1.74 MB
Free download PDF2.07 MB
Free download PDF1.39 MB
Free download PDF2.45 MB
Free download PDF4.87 MB
Complete guides for changing the Drop links on different SEAT EXEO models
Free download PDF1.32 MB
Free download PDF1.32 MB
Free download PDF1.41 MB
Free download PDF972.8 KB
Free download PDF1.19 MB
Free download PDF1.33 MB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your SEAT Exeo ST (3R5)
View more
How to prevent car windows from fogging up | AUTODOC tips
What to do if your car's air conditioning isn't working properly | AUTODOC tips
How to replace the suspension on a BMW E30 Turbo | SUPERCAR AUTODOC
How to paint a car with a spray can | AUTODOC tips
